Bladesmithing

The Best Steel for Your First Forged Knife (and Why 1084 Wins)

Why 1084 is the go-to steel for a first forged knife, how it compares with 1080, 80CrV2, 1095, 5160 and O1, and which steels beginners should skip for now.

On this page
  1. The short answer
  2. What makes a steel beginner-friendly
  3. Why 1084 is the usual recommendation
  4. Good alternatives
  5. Comparison table
  6. Steels to skip for now
  7. Thinking about Damascus? 1084 and 15N20
  8. Buying your first bar

The short answer

For most beginners, the best steel for a first forged knife is 1084. It’s a simple high-carbon steel that forges easily and hardens reliably in commonly available oils, without needing precise temperature control. That makes it far more forgiving than most alternatives.

1080 and 80CrV2 are close runners-up. 5160 is a good pick for larger, tougher blades. 1095 and O1 are fine steels that are a little less forgiving at home. Stainless steels and unknown scrap are best left until you’ve got some experience.

What makes a steel beginner-friendly

When you’re learning, the steel should forgive small mistakes. The traits that matter most are:

  • Simple heat treatment. Steels that harden at a single, fairly low temperature, without a long hold, are easier to get right with a forge and a magnet.
  • Oil hardening. Steels that harden in oil are less likely to crack than steels that need water or brine.
  • Easy forging. Some steels move readily under the hammer, while others are stiff and have narrow temperature ranges.
  • A known composition. If you know exactly what it is, you can look up the right temperatures.
  • Availability and price. You’ll ruin a few blades while learning, so cheap and easy to find helps.

Why 1084 is the usual recommendation

1084 is a plain carbon steel with roughly 0.8% carbon and little else in the way of alloying. That carbon level sits close to the “eutectoid” point of iron and carbon, which in practical terms means a few useful things for beginners:

  • It hardens easily. The carbon goes into solution quickly once the steel reaches hardening temperature, so it doesn’t need a long hold.
  • The magnet test works well. Its hardening temperature sits just above the point where steel stops being magnetic. That makes a simple magnet a reasonable, if rough, guide.
  • It hardens in common oils. 1084 will harden well in commercial quench oils and, for thinner blades, in warmed canola oil, which is what many beginners use.
  • It forges nicely. It moves well under the hammer at normal forging temperatures.
  • It’s widely sold by knife making suppliers in sheets and bars at reasonable prices.

Properly heat treated, 1084 makes a good working knife with decent edge retention and good toughness. Plenty of experienced makers keep using it long after their first blade.

The full process for 1084 is covered in our guide to how to heat treat a knife at home.

Its weaknesses

1084 isn’t perfect:

  • It rusts. Like all carbon steels, it needs to be kept dry and oiled. It’ll develop a patina with use.
  • Its edge retention is moderate. High-alloy steels hold an edge longer, at the cost of a far more demanding heat treatment.
  • It’s not tolerant of overheating. Getting it much too hot during forging or hardening can grow the grain and weaken the blade, so it isn’t idiot-proof.

Good alternatives

1080

1080 is very similar to 1084, with a slightly different carbon range. In practice it behaves almost the same way and is a good substitute if that’s what your supplier has.

80CrV2

80CrV2 is a carbon steel with small additions of chromium and vanadium. Many makers find it forgiving and like the toughness it gives. Its heat treatment is fairly close to 1084’s, though it often benefits from a short hold at hardening temperature. Check your supplier’s recommendations.

1095

1095 has more carbon than 1084 and can get slightly harder. It’s a classic knife steel. The catch for beginners is that it needs a faster quench to harden fully, and a slower oil may leave thicker sections soft. Faster quenchants increase the risk of cracks. It’s very usable, but less forgiving.

5160

5160 is a spring steel with less carbon and some chromium. It’s known for being very tough, which makes it popular for choppers, larger blades and swords. It won’t get quite as hard as 1084 and doesn’t hold a fine edge as long. It’s a good choice if your first project is a larger blade that’ll see heavy use.

O1

O1 is an oil-hardening tool steel. It machines well and makes excellent blades, but it typically needs a hold time at a controlled temperature during hardening. That’s hard to manage in a forge without a thermocouple. It’s a better choice once you have a heat treating oven.

Comparison table

This is a rough guide for home heat treatment and individual results depend heavily on the process.

Steel Ease of home heat treat Typical strengths Main drawback for beginners
1084 Very easy Forgiving, good all-rounder Rusts, moderate edge retention
1080 Very easy Similar to 1084 Same as 1084
80CrV2 Easy Toughness Benefits from a short soak
5160 Easy to moderate High toughness, good for big blades Less hardness than 1084
1095 Moderate Can get very hard Needs a fast quench, crack risk
O1 Moderate to hard Fine edge, machines well Needs accurate soak temperature

Steels to skip for now

Stainless steels

Stainless knife steels are excellent once heat treated properly, but most need high, precisely controlled hardening temperatures, specific hold times and often a foil wrap or controlled atmosphere. Many also need extra steps like cold treatment to reach their best performance. That’s very difficult to manage reliably in a forge. Many are also tougher to forge than carbon steels. If you want a stainless knife, many makers grind it from bar stock and send it to a professional heat treater.

Mystery scrap

Old files, leaf springs, saw blades and other recycled steel can make good knives. Smiths have used them for a long time. The problem is that you don’t know exactly what they are:

  • Different manufacturers and eras used different steels.
  • Some modern files may be case-hardened low-carbon steel rather than through-hardening high-carbon steel.
  • Springs and saw blades can carry fatigue cracks or damage you can’t see.

Without knowing the steel, you can’t look up its heat treatment, and when something goes wrong you can’t tell whether it was your process or the material. A known steel takes the guesswork out while you learn. Once you’re confident, scrap can be a fun experiment.

Thinking about Damascus? 1084 and 15N20

If you plan to try pattern-welded Damascus later, 1084 is also one of the most common steels for it. It’s often paired with 15N20, a carbon steel with added nickel. The nickel content helps it stay bright after etching, while 1084 etches dark. The two weld well together and respond to similar heat treatments.

Forge welding is a skill of its own, so most smiths make some single-steel knives first. When you’re ready, see our guide to making mosaic Damascus steel.

Buying your first bar

  • Buy from a knife making supplier who can tell you the exact steel grade.
  • Pick a sensible size. For a small utility or kitchen knife, stock about 3/16 to 1/4 inch (roughly 5 to 6 mm) thick and 3/4 to 1 1/2 inches (about 20 to 40 mm) wide is common. Thinner stock forges faster and is easier when you’re learning hammer control.
  • Buy more than you need. You’ll want spare pieces for practice and for testing your heat treatment.
  • Ask for the data sheet. Many suppliers give recommended forging, hardening and tempering temperatures.

With a bar of 1084 and a forge, you’ve got everything you need for a first blade. Our guide to knife making in a gas forge takes you through the forging step by step.

The complete guide to bladesmithing

Knife Making in a Gas Forge: A Beginner's Bladesmithing Guide
Read the guide

Keep exploring

Guides from other topics

All topics →