Metals and Fuel

Mild Steel vs High Carbon Steel: Which to Forge as a Beginner

Mild steel or high carbon steel for your first forging? Compare how each moves, hardens, costs and fails, and learn when to step up to 1084 or 5160 for blades and tools.

On this page
  1. The short answer
  2. What the difference actually is
  3. How each behaves under the hammer
  4. Hardening: the reason high carbon steel exists
  5. Side-by-side comparison
  6. Why mild steel is the right first steel
  7. When to move to high carbon steel
  8. Good first high carbon steels
  9. Telling them apart in your scrap pile

The short answer

Start with mild steel. It’s cheap, easy to find, forgiving of mistakes and moves well under the hammer across a wide range of heat. It’s the right material for learning to draw out, taper, bend, scroll, twist and punch, and for hooks, brackets, bottle openers, fire pokers and decorative work.

Move to high carbon steel when you want to make things that must harden: knives, chisels, punches, springs and other tools. Pick a simple, well-documented steel such as 1084 for your first blades.

What the difference actually is

Both are plain carbon steels: iron with a small amount of carbon. The amount of carbon changes everything.

  • Mild (low carbon) steel usually contains roughly 0.05–0.25% carbon. Common examples are A36 structural steel and 1018 bar.
  • Medium carbon steel sits roughly between 0.3% and 0.6%.
  • High carbon steel is roughly 0.6% carbon and up. Popular smithing steels include 1084 (about 0.84% carbon), 1095 (about 0.95%) and 5160 (about 0.6% carbon plus some chromium).

Carbon is what lets steel harden when quenched. Mild steel has too little to harden usefully. High carbon steel has enough to become very hard and then be tempered back for toughness.

How each behaves under the hammer

Mild steel is forgiving:

  • it forges across a broad heat range, from bright yellow down to a fairly dull red for light work
  • it rarely cracks if you hammer it a bit cool
  • it tolerates being left in a hot fire better than high carbon steel, though it can still burn at welding heat
  • no heat treatment is needed afterwards

High carbon steel is less forgiving:

  • it feels stiffer, so each blow moves less metal
  • it has a narrower working range. Overheat it and it can burn (you’ll see sparks coming off the bar in the fire), and you’ll lose carbon from the surface. Hammer it too cold and it can crack.
  • it needs normalising, hardening and tempering to be useful, and mistakes in heat treatment can mean warping, cracking or a soft edge

Practically, a beginner who struggles to manage heat will have a much easier time with mild steel, and will learn heat control there before it matters.

Hardening: the reason high carbon steel exists

Heat high carbon steel to its hardening temperature (around non-magnetic for simple steels like 1084), quench it in a suitable oil, and it becomes very hard but brittle. Tempering in an oven or with careful colour work then trades a little hardness for toughness. That’s how you get a knife that holds an edge or a punch that doesn’t mushroom.

Mild steel doesn’t harden in a useful way. Quench it and it stays soft enough to file. That’s why a mild steel knife will bend and dull quickly, and why mild steel is the wrong choice for tools that strike or cut.

Side-by-side comparison

Mild steel High carbon steel
Typical carbon ~0.05–0.25% ~0.6% and above
Common grades A36, 1018 1084, 1095, 1080, 5160, W1
Ease of forging Very easy Harder work, stiffer
Working heat range Wide Narrower; avoid overheating and working cold
Risk of cracking Low Higher if worked too cold or quenched badly
Hardens when quenched? Not usefully Yes
Heat treatment needed No Yes: normalise, harden, temper
Cost and availability Cheap, at any steel supplier More expensive; specialist suppliers for good grades
Best uses Practice, hooks, hardware, decorative work, structural pieces Knives, chisels, punches, springs, tool steel parts

Why mild steel is the right first steel

  • You’ll waste a lot of steel learning. Better that it’s cheap steel.
  • It lets you focus on hammer control. You can learn tapers, shoulders, scrolls and twists without fighting the material.
  • It teaches heat management with low stakes. Getting a feel for colour and timing in mild steel carries straight over to high carbon work.
  • The projects are genuinely useful. S-hooks, wall hooks, coat racks, fire pokers, bottle openers and leaf keychains are all classic mild steel projects. So are tongs, which are normally made from mild or medium carbon steel rather than hardenable tool steel.

One caution: some sources point out that cheap structural mild steel such as A36 can vary in composition, and occasionally a batch is harder or less consistent than expected. It’s still fine for practice. If you want predictable stock, 1018 is a more consistent low carbon option.

When to move to high carbon steel

You’re probably ready when you can:

  • hold a consistent heat and know when to stop and reheat
  • draw a clean, even taper without twisting or folding over the end
  • forge to a drawing or template reasonably accurately

At that point, high carbon steel opens up tools for your own shop, such as punches, chisels and drifts, and, for many people, the first knife.

Good first high carbon steels

  • 1084: widely recommended for first blades because its heat treatment is relatively simple and forgiving.
  • 1080 and similar: much like 1084, and often used interchangeably by hobbyists.
  • 5160: a tough spring steel, good for larger blades, choppers and tools that take impact.
  • 1095: can get very hard and hold an excellent edge, but it’s less forgiving in the quench and better saved for when you have some experience.

Buying known steel from a supplier removes guesswork from heat treating. That’s a big reason many smiths recommend it over scrap for first blades.

Telling them apart in your scrap pile

Scrap and salvage are a cheap source of both kinds of steel, but you’ll need to sort them. A grinder spark test shows mild steel as long streaks with few bursts and high carbon steel as a bushy stream with many bright starbursts. A quick quench-and-file test then confirms whether a piece hardens. Old ironwork can also turn out to be genuine wrought iron, which forges differently from both. See wrought iron forging techniques if that’s what you’ve found.

The complete guide to metals and fuel

What Wrought Iron Is Used For
Read the guide

Keep exploring

Guides from other topics

All topics →