Why wrought iron forges differently from steel
Genuine wrought iron is nearly carbon-free iron with threads of slag running along its length. That structure explains almost every quirk you’ll meet at the anvil:
- It behaves a bit like wood with a grain. It’s strong along the fibres and weaker across them.
- It generally prefers to be worked hot. Hammered too cold, the fibres can separate and the bar splits, frays or opens up.
- The slag acts as a natural flux, so it forge-welds very readily.
- It won’t harden by quenching. You can’t make a cutting edge from it alone.
If you’re used to mild steel, the main habit to change is your working heat. For more on what the material is and where it came from, see our overview of what wrought iron is used for.
Before you start: checking and preparing salvaged stock
Since commercial production stopped (we explain why in why wrought iron is no longer used), nearly all wrought iron is salvage: cart tyres, chain, fence rails, old bolts and architectural ironwork. Quality varies a lot.
- Confirm it’s wrought iron. A spark test against a known sample, a nick-and-bend test on an offcut, or a quick etch on a cleaned end will usually tell you.
- Look for delamination. Rusty old stock often shows lines or cracks along its length where corrosion has followed the slag. Badly layered bar may need welding back together, or it may be suitable only for practice.
- Clean off heavy rust and scale with a wire brush or grinder, and watch for old paint. Some old paint contains lead, so don’t burn or grind it without suitable precautions.
- Test a short piece first. Heat it and give it a few heavy blows, a bend and a twist to see how this particular batch behaves before you commit to a project.
Heat: work it hotter than you would mild steel
Most smiths who work wrought iron regularly suggest forging it at a bright yellow heat for heavy moves and stopping before it drops to a dull red. Exact advice varies with the quality of the iron, but the pattern is consistent:
- Heavy forging: high heat, bright yellow toward light yellow.
- Light finishing work: a bright orange is often fine for gentle blows.
- Stop and reheat sooner than you would with mild steel. If you see cracks opening along the bar, it’s too cold.
Wrought iron is generally tolerant of high heat. It can be taken close to welding heat without the burning problems high carbon steel has, though you can still burn it if you leave it sitting in an oxidising fire at welding heat. Keep a clean, deep fire and turn the work.
Core techniques
Drawing out
Drawing out (making the bar longer and thinner) is usually the easiest move, because you’re working with the grain. Keep it hot, use firm blows and rotate the bar regularly. If the corners start to split, round the corners slightly by working an octagon, then bring it back to square at a good heat.
Upsetting
Upsetting (thickening by driving the bar into itself) works against the grain, so wrought iron is more likely to split here. Tips:
- heat only the section you want to upset, as hot as practical
- keep blows square so the bar doesn’t buckle
- work in short sessions with frequent reheats
- if a seam opens, take it to welding heat and close it before carrying on
Bending and scrolling
Wrought iron bends nicely when hot and was the traditional material for scrollwork. Bend at a good orange-to-yellow heat. Sharp bends, especially on the outside of a tight corner, can open cracks along the fibres. For crisp corners, some smiths upset the corner area first so there’s extra material.
Twisting
Twisting stresses the fibres heavily, and poor-quality wrought iron can split or “unravel” in a twist. Higher-quality iron twists well and can show attractive grain once finished. To reduce the risk:
- use an even heat along the whole section being twisted
- twist at a higher heat than you would mild steel
- twist slowly and evenly, and stop if you see the corners opening
- try a sample from the same bar first
Punching, drifting and splitting
Punched holes in wrought iron were traditional and work well when hot. The fibres flow around the hole rather than being cut, as they would be with drilling. Keep the punch cool and the work hot, punch from both sides, and drift to final size at a good heat. Hot splitting with a chisel also works, though splits can follow the grain, so check your line as you go.
Forge welding
This is where wrought iron shines. The silicate slag helps the weld, and many smiths weld clean wrought iron with little or no added flux, though flux does no harm and helps with dirty or rusty stock. General approach:
- Scarf (taper) the pieces so they overlap and the weld squeezes slag outward.
- Bring them to a full welding heat in a clean, deep fire. The surface should look wet and glossy.
- Bring the pieces together quickly and set the weld with light, quick blows, then work it more firmly once it’s holding.
- Take a second welding heat to consolidate before forging the joint to shape.
The same ease of welding is why chain links, wagon tyres and larger bars were traditionally welded up from wrought iron. Historically, smiths also welded a steel edge onto a wrought iron body for axes and edge tools. Choosing a steel for that edge is covered in mild steel vs high carbon steel.
Refining poor-quality wrought iron (faggoting and re-piling)
Common or low-grade wrought iron can contain a lot of slag and splits easily. The traditional fix was to pile or faggot it: cut the bar into pieces, stack them, weld the stack at a full welding heat and draw it back out. Each cycle squeezes out more slag and gives a more uniform bar. It’s fuel- and time-heavy, but it can turn poor salvage into usable stock.
Finishing: wire brushing, oil and etching
- Hot wire brushing removes loose scale and leaves a clean, dark surface.
- Oil or wax finishes, such as boiled linseed oil or beeswax blends applied warm, are traditional for indoor work. Outdoor work usually needs a proper paint system.
- Etching brings out the grain. A cleaned, polished surface left in a suitable etchant shows the slag fibres as visible lines. Follow the etchant manufacturer’s safety instructions, wear eye and skin protection and ventilate well.
Common problems and fixes
| Problem | Likely cause | Fix |
|---|---|---|
| Bar splits along its length | Worked too cold, or poor-quality iron | Work hotter; weld the split closed at welding heat; refine stock by piling |
| Corners crack when drawing | Sharp corners cooling quickly | Work to an octagon, then back to square while hot |
| Twist unravels | Uneven heat or low-grade iron | Even heat, slower twist, test a sample first |
| Weld won’t take | Fire dirty or not hot enough; scale on the surfaces | Clean the fire; reach full welding heat; flux dirty stock |
| Surface looks pitted and stringy | Old corrosion along the grain | Grind back or accept it as part of the look |
Quick answers
What are the three types of forging?
In industry, forging is often grouped as open-die forging (shaping between flat or simple dies, much like hand forging at an anvil), closed-die or impression-die forging (metal pressed into a shaped cavity) and seamless rolled ring forging. Other sources split forging by temperature instead: hot, warm and cold forging. Traditional blacksmithing, including wrought iron work, is essentially hot, open-die forging.
How did medieval forges get hot enough?
Medieval smiths used charcoal and forced air from bellows. A compact bed of charcoal with a steady blast of air reaches welding heat. Bloomeries used the same principle on a larger scale to reduce iron ore directly into wrought iron, without ever fully melting it. For a look at how charcoal compares with modern forge fuels, see coal vs coke vs charcoal.