Forge Building

Forge Blowers Explained: Types and How They Work

What a forge blower does, how bellows, hand-crank and electric blowers work, how to control airflow, plus buying tips for vintage blowers and gas forge use.

On this page
  1. What a forge blower does
  2. From bellows to electric fans: a short history
  3. Types of forge blower
  4. How a centrifugal blower works
  5. Controlling the airflow
  6. Blowers on gas forges
  7. Buying a vintage hand-crank blower
  8. Care and maintenance

A forge blower is the device that pushes air into a forge fire. Coal, coke and charcoal fires get much hotter when air is forced through them. Without it, a solid-fuel forge smolders rather than reaching welding heat. Some gas forges also use blowers to feed their burners.

What a forge blower does

In a solid-fuel forge, the blower sends air through the tuyere, a pipe that opens into the bottom or side of the fire. More air means a hotter, faster-burning fire. Less air lets the fire idle and saves fuel. The smith controls the heat mainly by controlling the air.

A good forge blower:

  • Delivers a steady flow, not just a lot of air
  • Can be throttled easily, from a gentle idle to full blast
  • Keeps sparks and ash from blowing back into the blower

From bellows to electric fans: a short history

  • Bellows are the oldest forge air supply and were used for centuries. A single-chamber bellows gives a pulsing blast. A double-chamber design, sometimes called a “great bellows,” adds a second chamber that stores air under a weighted top board, so the blast stays more continuous.
  • Hand-crank rotary blowers became widely manufactured by the late nineteenth century. A geared crank spins a fan at high speed, giving a smoother, more controllable blast than bellows from a much smaller machine. Makers such as the Champion Blower & Forge Company and the Buffalo Forge Company produced them in large numbers, and many still work today.
  • Electric blowers took over in many shops through the twentieth century. They give a constant blast, with the flow controlled by a valve or by motor speed.

Types of forge blower

Bellows

Bellows are quiet, need no electricity, and many people value them for their traditional look and feel. They’re bulky, though, and pumping them keeps one hand or foot busy. Single-chamber bellows deliver air in pulses unless you work them steadily or use two.

Hand-crank blowers

A crank drives a gear train that spins a fan inside a housing. A few turns of the crank give many turns of the fan. Some have a clutch or freewheel mechanism that lets the fan coast between cranks. Hand-crank blowers give fine, responsive control: crank faster for more heat, slower to idle. They’re popular with smiths who want to work without power or prefer the traditional approach.

Electric centrifugal blowers

Most modern forge blowers are small electric centrifugal blowers, sometimes called squirrel-cage blowers. They’re compact and give a steady flow. Many deliver more air than a small forge needs, so they’re normally paired with a valve.

Improvised blowers

For first forges, many smiths use what they have:

  • Hair dryers, on the cool or no-heat setting where possible
  • Shop vacuums, connected to the exhaust or blower port
  • Inflatable or bounce-house blowers
  • Salvaged furnace or bathroom fans, depending on their pressure

These can work well, but almost all need throttling. Some aren’t designed to run continuously for long sessions.

How a centrifugal blower works

A centrifugal blower has an impeller, a wheel with many blades, inside a spiral housing. As the impeller spins, it throws air outward from the center to the edge of the housing. The spiral shape gathers that air and directs it out of a single outlet. New air is drawn in at the center, so the flow is continuous. Centrifugal blowers can push air against more resistance, such as a bed of coal, than a simple axial fan of similar size, which is why they suit forges well.

Controlling the airflow

  • Gate or blast valve: a sliding plate or butterfly valve in the air pipe. This works with any blower and is the most common method.
  • Bypass or dump: an opening before the tuyere that lets excess air escape. It’s simple, and helpful with powerful improvised blowers.
  • Motor speed control: convenient, but only suitable for some motor types. Dimmer-style controllers suit some motors and can damage others. Check that the controller is rated for your blower’s motor before using one.
  • Crank speed on hand-crank blowers, or pumping rate on bellows.

Whatever you use, keep the blower inlet clear and position the blower so sparks and ash can’t fall back into it.

Blowers on gas forges

Gas forges come in two broad types:

  • Naturally aspirated (venturi) burners draw their own air and need no blower.
  • Blown (forced-air) burners, including ribbon burners, use a blower to supply air, with the gas fed in separately. They give strong control over the fuel-air mix and are less affected by back pressure in the forge.

One safety point is important with blown burners: if the blower stops, the gas may keep flowing. Some builders add interlocks or a fail-safe arrangement so the gas shuts off when the air does. Always know how you’ll shut off gas quickly. Tuning blown burners is covered in how to tune a propane forge burner.

Buying a vintage hand-crank blower

Old hand-crank blowers turn up at farm sales, flea markets and online. Before buying:

  • Turn the crank. It should spin smoothly. Grinding, binding or a lot of free play suggests worn gears or bearings.
  • Listen and watch the fan. It should spin freely and keep spinning briefly after you stop. Rubbing against the housing is a warning sign.
  • Check the housing for cracks, especially on cast-iron parts, and make sure the outlet is intact.
  • Look for the oil fill or bath. Many blowers were designed to run with oil in the gearbox. A blower that’s been run dry for years may have worn gears.
  • Check that it mounts to your forge or can be adapted to it.

Care and maintenance

  • Keep gearboxes oiled according to their design. Some take oil, others grease.
  • Stop ash and coal fines from getting into the fan housing.
  • For electric blowers, keep the motor dry, clear of dust and well away from the heat.
  • Check air pipes and tuyeres periodically for blockages and burned-through sections.

For how the air supply ties into a solid-fuel forge, see how to build a coal forge firepot and tuyere. For cheap air sources on a first build, see building a forge on a budget.

The complete guide to forge building

How to Build Your Own Blacksmith Forge: Plans for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →