Forge Building

How to Build a Coal Forge Firepot and Tuyere

Build a coal forge firepot and tuyere: typical dimensions, steel plate choice, ash dump and clinker breaker, connecting the blower, and no-weld alternatives.

On this page
  1. How the firepot and tuyere work together
  2. Firepot shape and dimensions
  3. Materials
  4. Building a welded steel firepot
  5. Building the tuyere and ash dump
  6. Clinker breakers and grates
  7. Connecting the air supply
  8. Mounting the firepot in a hearth
  9. No-weld alternatives
  10. First fire and fire management
  11. Common mistakes

The firepot and tuyere are the heart of a bottom-blast coal forge. The firepot holds and shapes the fire. The tuyere delivers air into it from below and lets you dump ash and clinker. Get these right and the rest of the forge, the table or hearth around them, is straightforward.

How the firepot and tuyere work together

In a bottom-blast forge:

  1. Air from a blower or bellows enters the tuyere pipe below the firepot.
  2. It passes up through a grate or set of holes in the bottom of the firepot.
  3. It feeds the coal sitting in the firepot, creating a hot, concentrated fire.
  4. Ash and clinker fall, or are knocked, down through the grate into the ash dump at the bottom of the tuyere, which you can open to empty.

The sloped sides of the firepot help keep coal feeding down toward the hottest zone. Coal banked around the edge slowly cokes, ready to push into the fire.

Firepot shape and dimensions

There’s no single correct size, and smiths debate it at length. Common features are:

  • A tapered, bowl-like shape: wider at the top than at the bottom, with sloped sides
  • Depth: many hobby firepots are roughly 4 to 6 inches deep
  • Top opening: often somewhere around 8 to 12 inches across, square or rectangular
  • Bottom: a much smaller flat area containing the air grate

Smaller, shallower pots suit small stock and save fuel. Larger, deeper pots hold a bigger fire for heavier work. If you’re not sure, a moderate size toward the middle of these ranges is a reasonable starting point for general hobby smithing.

Materials

  • Steel plate for a welded firepot: fairly thick plate is commonly used, often in the 1/4 to 3/8 inch range, so the pot doesn’t burn through or warp quickly. Thicker plate lasts longer.
  • Cast iron: commercially made cast iron firepots are widely available and durable. Buying one and building the tuyere and table yourself is a common middle path.
  • Tuyere pipe and fittings: black steel pipe, often around 2 inches. Never use galvanized pipe or fittings. The zinc coating can give off harmful fumes when heated.
  • Grate: a thick steel plate with holes or slots, or a few steel bars.

Building a welded steel firepot

  1. Lay out the four side pieces as trapezoids, wider at the top than the bottom, and a small bottom plate. Cardboard templates help you check the fit before cutting steel.
  2. Bevel the edges to be welded so you get full penetration on the joints.
  3. Tack the sides together around the bottom plate, check that the shape is square and even, then weld it out fully.
  4. Cut the air opening in the bottom plate. Either drill a pattern of holes or cut a single opening covered by a removable grate. Keep the holes small enough that coal doesn’t fall through; their combined area should be roughly similar to the tuyere pipe’s cross-section so airflow isn’t choked.
  5. Add a flange or lip around the top edge if you plan to set the firepot into a table. This lets it rest on the table surface.
  6. Weld a short pipe stub or flange under the air opening to connect the tuyere.

Building the tuyere and ash dump

The simplest tuyere is a pipe tee below the firepot:

  • Top of the tee: connects to the firepot’s air opening
  • Side of the tee: connects to the blower or bellows
  • Bottom of the tee: the ash dump, closed with a hinged flap, a weighted door or a removable cap

A gravity flap held shut by its own weight or a counterweight is popular. You just knock it open to drop the ash. Keep the ash dump long enough that hot ash falls clear of the blower inlet, and make sure nothing flammable sits underneath.

Clinker breakers and grates

Coal leaves behind clinker, a glassy, fused waste that collects at the bottom of the fire and blocks airflow. Two common ways to deal with it:

  • Lift it out with a poker or small rake as it forms. This works with any firepot.
  • Clinker breaker: a rotating grate, often a triangular or bar-shaped piece of steel, turned by a handle below the forge. Turning it breaks up clinker and drops it into the ash dump.

Simple fixed grates are easier to build and are fine for many hobby forges.

Connecting the air supply

  • Run a pipe from the blower to the side of the tuyere tee.
  • Add a gate valve or sliding blast gate so you can control the air precisely.
  • Keep the blower a little distance from the forge and protect it from heat and falling ash.

Our guide to forge blowers explains hand-crank, electric and improvised options and how to throttle them.

Mounting the firepot in a hearth

  • Steel table: cut a hole in a steel table top to fit the firepot and rest it on its lip. Bolt or weld it in place.
  • Brick or clay hearth: set the firepot into a hearth built up from hard firebrick or packed clay around it. See building a hard firebrick forge.
  • Height: a common guideline is to set the fire at roughly knuckle height with your arm hanging naturally, but adjust to suit how you work.
  • Space: leave some flat hearth area around the firepot for banking coal.

Indoors, a coal forge needs a properly designed hood and chimney to carry smoke and gases outside.

No-weld alternatives

  • Brake drum forge: a cast iron truck brake drum makes a ready-made firepot. Add a tee below the center hole for air and ash.
  • Clay-lined forge: shape a firepot depression from clay, or a clay-and-sand mix, in a steel tray or box, around a tuyere pipe. Let it dry thoroughly before firing.
  • Side-blast design: run the tuyere in from the side instead of the bottom, as in a JABOD. This avoids building a bottom firepot altogether.

See building a forge on a budget for more low-cost designs.

First fire and fire management

  1. Start a small fire of paper and kindling over the tuyere opening, with light air.
  2. Add coal around it and let the fire grow.
  3. As the coal heats, it releases smoke and turns into coke, the light, porous fuel that gives a clean, hot fire.
  4. Keep fresh coal banked around the edge of the fire to coke slowly, and push coke into the center as needed.
  5. Place the steel in the hot heart of the fire, with burning coke below and around it. Directly above the tuyere, where the incoming air is richest in oxygen, steel tends to scale heavily. Perched on top of the fire, it heats slowly.

Use only as much air as the job needs. Too much burns fuel fast and can burn thin stock.

Common mistakes

  • Galvanized pipe or fittings anywhere in the hot zone or air path near the fire
  • Air holes that are too large, letting coal fall through, or too small, choking the air
  • A firepot that’s too big for the work, which wastes fuel and makes the fire hard to control
  • No way to dump ash, so the tuyere clogs mid-session
  • The blower too close to the forge, where it picks up heat or ash
  • Poor ventilation indoors. Coal smoke and carbon monoxide are hazards.

For an overview of other forge types, see our beginner’s guide to building a blacksmith forge.

The complete guide to forge building

How to Build Your Own Blacksmith Forge: Plans for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →