Learning Blacksmithing

Blacksmithing Safety for Beginners: Gear, Burns and Shop Rules

Blacksmithing safety for beginners: protective gear, ventilation and carbon monoxide, galvanized steel fumes, quench oil fires, grinders and basic burn first aid.

On this page
  1. The core safety rules
  2. Personal protective equipment
  3. Fire, fuel and ventilation
  4. Handling hot metal
  5. Toxic fumes: galvanized, plated and painted metal
  6. Quenching and oil fires
  7. Grinders and power tools
  8. Ergonomics: protecting your body
  9. Shop rules for visitors, kids and pets
  10. Burn first aid
  11. Your shop safety kit

The core safety rules

Blacksmithing is safe enough to enjoy for a lifetime, as long as you respect fire, hot metal and fumes. Learn these rules before anything else:

  1. Always wear safety glasses in the shop, whether you’re forging, grinding or just watching.
  2. Wear natural fibers such as cotton, wool or leather. Synthetic fabrics can melt onto skin.
  3. Treat all metal as hot. Steel can cause a serious burn long after it stops glowing.
  4. Never forge galvanized, plated or painted metal unless you know what’s on it and have removed it safely.
  5. Ventilate. Forges produce carbon monoxide, and it can build up without you noticing.
  6. Protect your hearing. Hammer and anvil noise adds up.
  7. Keep a fire extinguisher and water within reach, and know how to use them.
  8. Keep the area around the forge clear of flammables, clutter and trip hazards.
  9. Keep bystanders, children and pets well back.
  10. Don’t forge when you’re tired, rushed or impaired.

This guide is a starting point. It doesn’t replace in-person instruction, the manufacturer’s instructions for your equipment, or medical advice.

Personal protective equipment

Eyes. Hot scale, sparks and bits of metal fly off the work, especially when hammering and grinding. Wear impact-rated safety glasses with side protection. In the US, look for the ANSI Z87.1 marking. Add a full face shield over your glasses for grinding. If you’ll be looking into a hot forge for long periods, some smiths use lightly shaded lenses to cut glare. Ask a supplier which shade suits your forge.

Ears. The ring of a hammer on an anvil can be very loud, and hearing damage builds up over time and is permanent. Use earplugs or earmuffs every session, not just for “loud” work.

Clothing. Wear cotton, wool or leather and avoid polyester, nylon and other synthetics. Long trousers without turn-ups (cuffs), worn over your boots, stop hot scale falling in. Avoid loose sleeves, scarves and hanging cords. Tie back long hair, and remove rings and dangling jewelry.

Apron. A leather apron protects your body from scale, sparks and accidental contact with hot work.

Hands. Many smiths wear a leather glove on the tong hand and keep the hammer hand bare or lightly gloved for grip. Gloves aren’t a heat shield: never pick up hot metal with a glove. Wet gloves can cause steam burns when they touch something hot. Gloves can also be dangerous around rotating machinery (see below).

Feet. Wear sturdy leather boots, ideally with protective toes. Avoid synthetic trainers and anything with mesh, which hot scale can burn through.

Lungs. Use a suitable respirator or dust mask when grinding, sanding or working with coal dust. Good ventilation is the first line of defence against fumes; a mask isn’t a substitute for it.

Fire, fuel and ventilation

Carbon monoxide (CO). Both propane and solid-fuel forges produce carbon monoxide, which you can’t see or smell. Early symptoms such as headache, dizziness, nausea and fatigue are easy to mistake for tiredness or heat. Forge outdoors or in a space with plenty of fresh air moving through it, and install a CO alarm in any enclosed shop. If you or anyone else feels unwell, shut off the forge, get into fresh air and seek medical help if symptoms don’t clear quickly.

Propane forges.

  • Follow the manufacturer’s instructions for setup, lighting and shutdown.
  • Keep propane cylinders outside the forge’s heat zone, upright and away from the work area.
  • Check hoses and connections for damage, and test for leaks with soapy water, never a flame.
  • Close the cylinder valve when you’re finished.
  • Make sure the forge has enough exhaust opening and the shop has enough ventilation.

Coal and charcoal forges.

  • These produce smoke as well as CO, so a chimney or hood with a good draw, or working outdoors, is important.
  • Keep a water can or bucket nearby to control the fire.
  • Make sure the fire is fully out at the end of the day, and store coal away from heat.

General fire safety. Keep a suitable fire extinguisher close to the forge (an ABC multipurpose type covers most common shop fires) and check it regularly. Clear sawdust, rags, paper and fuel containers from the area, and never leave a lit forge unattended.

Handling hot metal

  • Assume everything is hot. That includes the work, tools, tongs, the anvil face and anything near the forge.
  • Put hot pieces down in a set place, away from where people walk, and point sharp or hot ends away from you.
  • Mark hot work if others share the shop, for example by writing “HOT” in chalk.
  • Never grab dropped hot work. Let it fall and pick it up with tongs.
  • Use tongs that fit the stock properly. Poorly fitting tongs let work slip or fly out when you hit it.
  • Cool tools in water as you work, but be aware of steam.
  • Watch the far end of the bar. The end not in the fire can still be hot near the heated section, and long bars can swing into people.

Toxic fumes: galvanized, plated and painted metal

Galvanized steel is coated with zinc. When it’s heated to forging temperatures, the zinc gives off fumes that can cause metal fume fever, a flu-like illness. Repeated exposure is harmful. The safest approach for beginners is simply not to forge galvanized material.

Plated or coated parts from salvage and scrap can be worse. Some old hardware and fasteners are cadmium-plated, and cadmium fumes are highly toxic. If you don’t know what a coating is, don’t heat it.

Old painted metal may contain lead or other hazardous materials. Stick to clean, uncoated steel from a steel supplier, especially while you’re learning.

Quenching and oil fires

Quenching hot steel in oil, common in bladesmithing and tool making, can produce flames and smoke, and it can start a fire if done carelessly.

  • Use a metal container with a well-fitting metal lid to smother flames.
  • Never use water on an oil fire. Smother it with the lid, or use a suitable extinguisher.
  • Keep the quench container stable and in a place where it can’t be knocked over.
  • Use an appropriate quenching oil and follow any guidance on safe operating temperatures.
  • Do quenching in a well-ventilated area, away from your face, and wear eye protection.

Grinders and power tools

Grinders, belt sanders and drill presses cause many shop injuries.

  • Eye and face protection: wear glasses plus a face shield when grinding.
  • Gloves and rotating machinery: gloves can be caught by spinning wheels, belts, drill chucks and lathes, pulling your hand in. Many shops prohibit gloves on drill presses and lathes for this reason. Follow the tool manufacturer’s guidance and think about entanglement before wearing gloves near any rotating tool.
  • Sparks: grinding sparks can start fires. Clean up dust and keep combustibles away.
  • Guards and tool rests: keep them fitted and correctly adjusted.
  • Secure the work so it can’t be snatched from your hands.
  • Dust: grinding dust can be harmful to breathe. Use extraction or a respirator.

Ergonomics: protecting your body

Repetitive strain injuries are among the most common long-term problems for blacksmiths.

  • Set your anvil at a good height. Roughly knuckle height when you stand with your arms relaxed is a common starting point. Adjust from there.
  • Use a hammer weight you can control. A lighter hammer used well is better than a heavy one used badly.
  • Hold the hammer loosely. A death grip strains your forearm and elbow.
  • Let the arm and body work together rather than forcing every blow from the wrist or shoulder.
  • Take breaks, stay hydrated and stop if something hurts. Working in heat is tiring.

If you’re teaching yourself, these habits are easy to get wrong without noticing. Our self-learning roadmap suggests ways to get feedback, and a beginner class is worth it for this alone. See how to become a blacksmith for your options.

Shop rules for visitors, kids and pets

  • Mark a safe viewing area and make sure visitors stay in it.
  • Give anyone watching safety glasses and, ideally, hearing protection.
  • Keep children and pets well away from the forge, anvil and quench.
  • Tell visitors not to touch anything, because it may be hot.
  • Explain where the extinguisher and first aid kit are.

Burn first aid

Minor burns are common in blacksmithing. Knowing basic first aid matters. These steps reflect widely published first aid guidance, but they aren’t a substitute for medical advice.

For a minor burn:

  1. Move away from the heat source and stop the burning.
  2. Cool the burn under cool running water for about 20 minutes. Don’t use ice, iced water, butter or greasy creams.
  3. Remove rings, watches or tight clothing near the burned area before it swells, unless they’re stuck to the skin.
  4. Cover the burn loosely with a clean, non-fluffy dressing or cling film.
  5. Don’t burst blisters.
  6. Use a pain reliever if needed, following the label.

Get medical help promptly if:

  • The burn is large, deep, or looks white, leathery or charred.
  • It’s on the face, hands, feet, genitals or a major joint.
  • It’s a chemical or electrical burn.
  • The person is a child or an older adult, or is having trouble breathing.
  • You’re unsure how serious it is.

Call your local emergency number for severe burns. If something gets into your eye, don’t rub it; seek medical help.

Your shop safety kit

  • Safety glasses (several pairs, for visitors) and a face shield
  • Earplugs or earmuffs
  • Leather apron, gloves and boots
  • Fire extinguisher, checked regularly
  • Bucket of water near the forge
  • Metal lid for the quench tank
  • Carbon monoxide alarm for any enclosed space
  • First aid kit with burn dressings
  • A phone within reach
  • Chalk for marking hot work

If you’re taking a class, ask what safety gear is provided and what to bring. Our guide to learning costs covers budgeting for basic protective equipment.

The complete guide to learning blacksmithing

Blacksmithing Apprenticeships in the USA
Read the guide

Keep exploring

Guides from other topics

All topics →