Anvils and Tools

Blacksmith Tongs for Beginners: Which Types You Need First

Which blacksmith tongs beginners need first: flat jaw, V-bit and wolf jaw tongs, how to size them to your stock, check grip, adjust fit and look after them.

On this page
  1. The short answer: your first three pairs
  2. Why tong fit matters
  3. The main tong types
  4. Sizing tongs to your stock
  5. How to check a good grip
  6. Adjusting tongs to fit
  7. Tong rings and clips
  8. Looking after tongs
  9. Buy, make or start from blanks?
  10. You may need fewer tongs than you think

The short answer: your first three pairs

Most beginners can cover the bulk of early projects with two or three pairs of tongs, sized to the stock they use most:

  1. Flat jaw tongs for flat bar and for square bar held flat
  2. V-bit tongs for round and square bar held along their length
  3. Wolf jaw (universal) tongs for a mix of shapes and sizes

If your first projects use mostly 3/8 to 1/2 inch (about 10 to 12 mm) bar, buy or make tongs that fit that range. Add other types as your projects demand them.

Why tong fit matters

No pair of tongs holds everything well. A pair that grips one bar securely may let a slightly smaller or larger bar twist, slip or fly out under the hammer. Hot stock that comes loose is a real safety hazard. It can land on you, on the floor or somewhere flammable. Tongs matched to the size and shape of the work are always the safest choice. That’s why experienced smiths end up owning dozens of pairs.

Tongs sold as “universal” are more versatile than most, but they’re still not truly universal.

The main tong types

Flat jaw tongs

These are the simplest design: two flat, parallel jaws. They hold flat bar and sheet well. Some versions have a groove down the middle so they can grip round stock too. They’re often the first pair a new smith buys or makes.

V-bit tongs

The jaws have V-shaped grooves running along their length, which cradle round, square and hexagonal bar securely. They’re a very useful general pair for anyone working with round or square stock.

Wolf jaw (universal) tongs

Wolf jaw tongs combine features, typically a V or notch for round and square stock with flat sections for flat bar. They’re among the most versatile tongs for a beginner and a good third pair.

Bolt and box jaw tongs

These jaws have a curved or boxed section that lets them hold a bar end-on or grip stock with an upset or bulged section, such as a bolt head. They’re useful once you start upsetting or forging bar ends.

Pickup tongs

Pickup tongs have curved, pointed jaws for grabbing hot pieces of irregular shape, such as offcuts, dropped work and slugs. They’re handy, but not secure enough to forge with.

Blade tongs

These are shaped to hold knife blanks by the spine or tang. They’re needed mainly for bladesmithing.

Scrolling tongs

Scrolling tongs have narrow, rounded jaws for gripping the end of a bar and rolling it into a scroll. They’re useful for decorative work.

Sizing tongs to your stock

Tongs are made to fit a range of stock sizes, not just one. When choosing or making tongs:

  • Check the stated size range and match it to the bar you use most.
  • Bigger stock needs bigger jaws and longer, sturdier reins.
  • The jaws should open to the stock size with the reins comfortably apart, not touching and not spread too wide.
  • Longer reins relative to the jaw length give more grip for the same squeeze, because of leverage. Very long reins can make the tongs awkward to manage, though.

How to check a good grip

Before you put hot work under the hammer, check:

  1. The jaws contact the stock along their length, not just at the tips or just at the back.
  2. The jaws are roughly parallel when closed on the work.
  3. The reins don’t touch when gripping. If they do, the tongs can’t squeeze any harder.
  4. The reins aren’t spread uncomfortably wide, which tires your hand and loosens your grip.
  5. The work doesn’t twist when you wiggle it or tap it.

If any of these fail, use a different pair or adjust the ones you have.

Adjusting tongs to fit

Tongs can be tuned to a specific bar:

  • Heat the jaws (not the rivet or reins) to a forging heat.
  • Grip the bar you want to hold, cold.
  • Tap the jaws closed around it on the anvil so they match its shape.
  • Cool the tongs before use.

Many smiths tune a pair this way for each new project. It’s a quick fix that makes hot work much safer.

Tong rings and clips

A tong ring or clip slides over the reins to hold them closed. That lets you relax your grip during long forging sessions. It’s useful, but don’t rely on one to make poorly fitting tongs hold. If the tongs need a ring to stay on, they may be the wrong size.

Looking after tongs

  • Don’t leave tongs in the fire. Jaws that get hot enough to glow will soften and lose their shape.
  • Cool them often in the quench bucket while working.
  • Oil the rivet occasionally so the tongs open freely.
  • Check rivets and reins for cracks or looseness, and repair or replace damaged tongs.

Buy, make or start from blanks?

  • Buying ready-made tongs gets you working immediately. Quality varies, so expect to adjust the fit on cheaper pairs.
  • Making your own is a classic project, and teaches drawing out, punching and riveting. It isn’t the easiest first project, though. Many people make their first tongs after a few weeks of practice.
  • Tong blanks are pre-forged halves that you finish, fit and rivet yourself. They’re a good middle ground for learning while saving time.

You may need fewer tongs than you think

Plenty of beginner projects need no tongs at all. Forge on the end of a long bar, holding the cold end by hand, then cut the finished piece off. It’s a good habit to learn early, and it keeps costs down. Our guides to poorboy blacksmith tools and whether blacksmithing is a cheap hobby cover more ways to save.

Holding the work well is one of the core skills of a blacksmith. Pair your tongs with a well-chosen hammer (see choosing your first blacksmith hammer) and you’re most of the way to a working kit. The rest is in our essential blacksmithing tools guide.

The complete guide to anvils and tools

Blacksmithing Tools of the Trade: The Beginner's Essential Kit
Read the guide

Keep exploring

Guides from other topics

All topics →