Anvils and Tools

Hardy Tools Explained: What Goes in the Anvil's Hardy Hole

What hardy tools are used for: cutting hardies, bending forks, swages and fullers, how to fit them to your hardy hole, use them safely and make your own.

On this page
  1. What hardy tools are
  2. The hardy hole and the pritchel hole
  3. Common hardy tools and what they do
  4. Top and bottom tools
  5. Using a cutting hardy safely
  6. Fit: measuring and sizing shanks
  7. Which hardy tools to get first
  8. Making your own hardy tools
  9. No hardy hole? Alternatives

What hardy tools are

Hardy tools, also called anvil tools or bottom tools, are tools with a square shank that drops into the square hardy hole in an anvil. The square shank stops them turning while you work. They let the anvil do jobs it otherwise couldn’t, like cutting, bending, rounding and grooving hot metal, without leaving the anvil for a vise or another tool.

Strictly speaking, “hardy” on its own refers to the cutting tool, the most common of them. “Hardy tools” is used loosely for the whole family.

The hardy hole and the pritchel hole

Most anvils have two holes, usually near the heel:

  • The hardy hole is square and holds hardy tools. It’s also useful as an opening to bend over or drop work through.
  • The pritchel hole is round and smaller. Smiths use it when punching through hot stock, letting the slug fall through, and for holding some round-shanked tools.

Common hardy tools and what they do

Cutting hardy

The cutting hardy has a chisel-like edge facing up. You lay hot stock across the edge and strike it with the hammer to cut most of the way through, then break off the rest. It’s arguably the most useful hardy tool and the one most smiths get first.

Bending fork

A bending fork has two upright prongs. You put a hot bar between them and lever it to make bends, curves and scrolls. It’s simple, versatile and an easy tool to make yourself.

Bottom swages

Swages have grooves shaped to a particular cross-section, usually round, but also V or hexagonal. Hot stock hammered into the groove takes on that shape. They’re used to make bar round and even, or to finish tenons and rivet stock.

Bottom fullers and spring fullers

A bottom fuller has a rounded ridge. Pressing hot stock over it forms grooves and shoulders, and spreads metal in a controlled direction. A spring fuller combines top and bottom fullers on a springy steel loop, so you can fuller both sides at once without a helper.

Cones, bicks and stakes

Small cones or bicks (pointed horns) sit in the hardy hole to give you a smaller or differently shaped horn. They’re useful for small rings, eyes and curves. Stakes of other shapes can be made for particular jobs.

Holdfasts and other workholding

Some tools use the hardy or pritchel hole to clamp work to the anvil, freeing a hand for a punch or chisel. A holdfast is the traditional example.

Top and bottom tools

Many hardy tools have matching top tools. These are hammer-like tools with a handle, held on top of the work and struck. A top swage paired with a bottom swage of the same size forms round stock from both sides. A top fuller and bottom fuller together form matching grooves. Using top tools often needs a striker, a spring tool or a lot of practice.

Using a cutting hardy safely

The cutting hardy is very useful, but it needs care:

  • Never strike straight down onto the edge at the end of a cut. If your hammer hits the hardened edge, it can chip the hammer face or the hardy and throw fragments. Cut most of the way through, then finish by breaking or bending the piece off, or cut from both sides.
  • Control where the offcut goes. Short hot pieces can fly off. Point the cut away from yourself and others.
  • Remove the hardy when you’re not using it. An upright edge is easy to forget and painful to hit with a hand or arm.
  • Wear eye protection, as always.

Fit: measuring and sizing shanks

Hardy holes vary in size. Common sizes include 3/4 inch and 1 inch, with others found on different anvils. Before buying tools:

  1. Measure your hardy hole across the flats, and check whether it’s straight or tapered from top to bottom.
  2. Choose tools with shanks sized for your hole. Shanks are often made slightly undersize, and suppliers may expect some final fitting.
  3. Aim for a snug but free fit. The tool shouldn’t wobble badly, but it shouldn’t need hammering in either. A tool that’s too tight can jam as it heats up and expands.
  4. The tool’s shoulder should rest on the anvil face or sit just clear of it, so the load goes into the anvil body rather than wedging the hole.

When inspecting a second-hand anvil, check the hardy hole for cracks and distortion. See how to inspect a used anvil.

Which hardy tools to get first

For most beginners, in rough order:

  1. Cutting hardy. For cutting off finished pieces and stock.
  2. Bending fork. For hooks, scrolls and bends.
  3. Round bottom swage. For finishing round stock and tenons.
  4. Bottom fuller or spring fuller. For shoulders and grooves.

Add others as particular projects call for them.

Making your own hardy tools

Hardy tools are classic early projects:

  • Bending fork. Forge or weld two prongs to a square shank that fits your hardy hole. It needs no heat treatment and is a good first hardy tool.
  • Cutting hardy. Forge a wedge-shaped blade on a square shank from a suitable medium- or high-carbon steel, then harden and temper the edge. The same heat treating principles apply as in making chisels from old files.
  • Swages and fullers. Forge or machine the shape on top of a shank, or make bar-type tools to use in a vise.

Make the shank from square bar sized to your hole, with a shoulder forged or welded on so the tool sits at the right height.

No hardy hole? Alternatives

If your anvil has no hardy hole, as many improvised anvils don’t, you can still use most of these tools:

  • Clamp them in a leg vise. Many hardy tools are designed to work in a vise too.
  • Use a swage block, a heavy block with holes and shaped edges.
  • Mount a hardy-hole plate to your anvil stand next to the anvil.

See our guide to poorboy blacksmith tools for more ideas. When choosing an anvil, a standard-size hardy hole is a real advantage. See our anvil review.

Cutting, bending and fullering are central to the core skills of a blacksmith, and hardy tools make all three easier. For the rest of the beginner’s kit, see our essential blacksmithing tools guide.

The complete guide to anvils and tools

Blacksmithing Tools of the Trade: The Beginner's Essential Kit
Read the guide

Keep exploring

Guides from other topics

All topics →