Anvils and Tools

What are the 7 skills of a blacksmith?

The 7 core skills of a blacksmith: drawing out, upsetting, bending, twisting, punching, cutting and forge welding, plus the fire and hammer skills underneath.

On this page
  1. The short answer
  2. 1. Drawing out
  3. 2. Upsetting
  4. 3. Bending and scrolling
  5. 4. Twisting
  6. 5. Punching and drifting
  7. 6. Cutting and splitting
  8. 7. Forge welding
  9. The skills underneath the skills
  10. A sensible learning order
  11. Practice projects that combine the skills

The short answer

There’s no single official list, but blacksmithing is commonly taught as a small set of fundamental operations, and they group neatly into seven:

  1. Drawing out. Making a bar longer and thinner.
  2. Upsetting. Making a section shorter and thicker.
  3. Bending and scrolling. Changing direction and forming curves.
  4. Twisting. Rotating a section of bar along its length.
  5. Punching and drifting. Making and shaping holes.
  6. Cutting and splitting. Separating or dividing hot metal.
  7. Forge welding. Joining pieces by heating and hammering them together.

Almost everything a blacksmith makes, from a simple hook to a gate, combines these operations. Underneath them sit skills that aren’t techniques as such: managing the fire, reading the heat and controlling the hammer.

1. Drawing out

Drawing out lengthens a bar while reducing its cross-section. It’s the most-used operation in blacksmithing. Tapers, points and long thin sections all start here.

  • How. Hammer the hot bar on the anvil face, turning it 90 degrees regularly to keep it square. Working over the anvil’s edge or the horn, or using the hammer’s peen, pushes metal lengthwise faster.
  • Tools. A forging hammer and anvil, with tongs once the piece gets short. See our guide to choosing your first blacksmith hammer.
  • Practice. Draw a square taper to a point. It’s the start of hooks, nails and plant stakes.

2. Upsetting

Upsetting is the opposite of drawing out. It makes a section shorter and thicker. It’s used to make heads on bolts and nails, to add metal where you’ll punch a hole, or to build up a shoulder.

  • How. Heat just the section you want to thicken, then strike the end of the bar, or drive the bar down onto the anvil. Quenching the neighbouring areas keeps the swelling where you want it.
  • Watch for. The bar bending instead of thickening. Straighten it and continue.
  • Practice. Upset the end of a short bar, then forge it into a nail head.

3. Bending and scrolling

Bending changes the bar’s direction. Scrolling forms controlled spiral curves, a hallmark of decorative ironwork.

  • How. Bend over the anvil edge or horn, in a vise, or with a bending fork in the hardy hole. Heat only the section you want to bend.
  • Tools. A vise, bending forks and scrolling tongs all help. See hardy tools explained.
  • Practice. An S-hook: draw both ends to tapers, then scroll and bend them.

4. Twisting

Twisting rotates part of a square or flat bar along its length. It’s a simple way to add decoration and a satisfying early skill.

  • How. Heat the section evenly, clamp one end in a vise and turn the other with a wrench or tongs. An even heat gives an even twist.
  • Practice. Twist the handle section of a fire poker or the shank of a hook.

5. Punching and drifting

Punching makes a hole by displacing hot metal rather than drilling it out. Drifting then enlarges and shapes the hole to a precise size.

  • How. Punch partway from one side, flip the work and finish from the other, knocking out a small slug over the pritchel hole or a bolster. Then drive a drift through to size the hole.
  • Tools. Hot punches and drifts, often made by the smith from tool steel.
  • Practice. Punch a hole in a flattened bar end for a hanging tab, or make a small drifted eye.

6. Cutting and splitting

Cutting separates hot metal. Splitting divides a bar lengthwise, for example to make forks or decorative ends.

  • How. Use a hot chisel struck with a hammer, or a cutting hardy in the hardy hole. Cut most of the way from both sides, then break off the rest. Never hammer straight down onto a cutting hardy’s edge.
  • Tools. Hot cuts and hardies. Our guide to making chisels from old files covers making simple cutting tools and heat treating them.
  • Practice. Cut a finished hook off the parent bar, or split the end of a bar to make a two-tined fork.

7. Forge welding

Forge welding joins two pieces of iron or steel by heating them to a very high, near-white heat and hammering them together, often with a flux to keep the surfaces clean. It’s the traditional way to join metal without modern welding equipment, and it’s the basis of pattern-welded (“Damascus”) steel.

  • How. Clean and prepare the surfaces, bring them to welding heat with flux, then join them with quick, firm, well-placed blows.
  • Watch for. Burning the steel, which shows as a shower of sparks from the fire. Cold or dirty surfaces won’t stick.
  • Practice. Most people learn it after the other six. Simple faggot welds or a welded ring are traditional first attempts.

The skills underneath the skills

The seven operations rely on more basic abilities that develop with practice:

  • Fire management. Keeping a clean, hot fire or a properly tuned gas forge, and heating the right part of the bar.
  • Reading heat. Judging temperature from colour. Working in shade rather than direct sunlight makes this easier.
  • Hammer control. Accurate, repeatable blows using the right part of the hammer face, without tensing up.
  • Holding the work. Choosing and fitting tongs securely. See our tongs guide.
  • Heat treatment. Hardening and tempering steel for tools and blades.
  • Safety habits. Eye and ear protection, a tidy floor and respect for hot metal that doesn’t look hot.

A sensible learning order

Most courses and books introduce the skills in roughly this order:

  1. Fire management, reading heat and basic hammer control
  2. Drawing out and tapering
  3. Bending and scrolling
  4. Twisting
  5. Cutting
  6. Upsetting
  7. Punching and drifting
  8. Forge welding and heat treatment

Upsetting comes later than its place on the list suggests, because it’s hard to control at first. Forge welding is usually last.

Practice projects that combine the skills

  • S-hook: drawing out, bending, scrolling
  • Wall hook with a punched hole: drawing out, flattening, punching, bending
  • Fire poker: drawing out, twisting, bending
  • Nail: drawing out, cutting, upsetting
  • Bottle opener: punching, drifting, shaping

Our article on what blacksmiths craft has more project ideas. For the tools you’ll need to practise these skills, see our beginner’s essential blacksmithing kit.

The complete guide to anvils and tools

Blacksmithing Tools of the Trade: The Beginner's Essential Kit
Read the guide

Keep exploring

Guides from other topics

All topics →