Projects

Forging Nails: A Classic Blacksmith Exercise

How to forge a rose-head nail by hand: drawing the point, using a nail header, upsetting the head, fixing common problems, and why nails are such good practice.

On this page
  1. Why Nail Making Is a Classic Exercise
  2. Tools and Materials
  3. How to Forge a Rose-Head Nail
  4. Choosing or Making a Nail Header
  5. Common Problems and Fixes
  6. Nail Head Styles
  7. What to Do With Your Nails
  8. Do Blacksmiths Still Make Nails for a Living?

Forging a nail looks simple: a point, a shank and a head. But doing it well, quickly and the same way every time takes real control. That’s why so many smiths still use nails as a practice exercise and warm-up, long after machines took over making them. This guide covers the tools, the step-by-step process for a traditional rose-head nail, and the problems most beginners run into.

Why Nail Making Is a Classic Exercise

A single nail packs several core skills into a few heats:

  • Drawing a square taper. The shank needs four even faces coming to a centered point.
  • Hammer control. The work is small, so every blow counts, and stray blows show.
  • Cutting. You nick the bar partway through so the nail can be snapped off.
  • Upsetting. The head is formed by driving hot metal back into itself.
  • Heat management. A thin point heats and cools much faster than the bar behind it.

Nails are also fast and use very little steel, so you can make dozens in a session. Then you can line them up and see how consistent you’re getting. For a wider look at where nails fit among beginner builds, see our blacksmith project plans.

Tools and Materials

  • Stock: 1/4” square mild steel is a common choice. Smaller stock makes finer nails but is less forgiving. Work off the end of a long bar so you don’t need tongs.
  • Nail header: a bar or plate with a tapered hole that holds the shank while you form the head. More on this below.
  • Hammer: a hammer of moderate weight you can control well. Many smiths use a lighter hammer for nails than for general work.
  • Anvil: the far edge and a hardy cutoff tool (if you have one) are useful for cutting.
  • Forge: any forge that can bring the end of the bar to a bright orange to yellow heat.
  • Safety gear: safety glasses are essential. Small hot offcuts and scale fly around during this work.

How to Forge a Rose-Head Nail

The rose head is the classic hand-forged nail head: a slightly domed head with four or more facets, a bit like a flattened pyramid. The steps below describe one common sequence. Smiths vary the details.

1. Draw the Point

Heat the last couple of inches of the bar to a bright orange. Draw out a four-sided taper by hammering on one face, rolling the bar 90 degrees, hammering again, and repeating. Hold the bar at a slight angle to the anvil face so the taper forms toward the tip.

Keep checking that the cross-section stays square and doesn’t drift into a diamond. If it does, a few blows on the long corners will bring it back. Work quickly at the tip, which loses heat fast, and stop hammering once it dims to a dull red.

2. Mark the Length and Cut Partway Through

Decide how long the shank will be. Then leave a short stub of full-size bar above that point to form the head. With 1/4” stock, a stub roughly the length of the bar’s thickness or a little more is a reasonable starting point. Adjust it after your first few nails.

At a good heat, cut most of the way around the bar at that point. Use the hardy, a hot cut or the anvil’s edge, but don’t cut all the way through. The thin web that’s left lets you snap the nail off cleanly once it’s in the header.

3. Set the Nail in the Header

Reheat if needed. Drop the shank into the header hole. The tapered shank should pass through, while the full-size stub above the cut sits proud of the header. Snap or twist the bar off at the nick, leaving the stub standing up out of the header.

Hold the header steady over the anvil’s pritchel or hardy hole, or over the gap between the anvil and a block, so the shank can hang down freely.

4. Upset the Head

Work fast, because the stub is losing heat. Hit it squarely a few times to upset it into a short, thick button. Then, without stopping, use angled blows around the edge to form the facets of the rose head. Four angled blows give the classic four-faceted head. Some smiths add more for a rounder look.

If the stub cools before the head is finished, stop. Hammering cold steel in the header tends to give a cracked or lopsided head, and it can damage the header.

5. Release the Nail

Turn the header over and tap it on the anvil, or tap the point end, to knock the nail out. The upsetting should have filled the top of the hole slightly. A light tap is usually enough to free it. Set the nail aside to cool, then heat the bar again and start the next one.

Choosing or Making a Nail Header

You can buy a nail header from a blacksmith supplier or make your own. Whichever you choose, a few points matter:

  • The hole is tapered. It’s narrower at the bottom and opens slightly toward the top, so the shank wedges in and the head has something to sit on.
  • Hole size suits your stock. It should be large enough for the tapered shank to drop most of the way in, but small enough that the full-size bar above can’t pass through.
  • It’s made from a durable steel. A header takes repeated hot blows. One made from soft mild steel will work, but its hole will wear and spread over time. Many smiths make headers from tool steel or an old file or spring, hardened and tempered, but that’s a project in its own right.
  • It has a handle. Many headers are long bars with the hole near one end, or have a handle, so you can hold them away from the heat.

Some headers have a slightly raised boss around the hole. This lets you form a head that sits fully above the header surface, and some smiths find it makes the facets easier to shape.

Common Problems and Fixes

  • The nail sticks in the header. The hole may be too small or worn rough, or the head may have overfilled the top of the hole. Try a light tap from below, a slightly smaller shank, or cleaning up the hole.
  • The head is off-center. Usually the stub wasn’t upright when you started hitting, or the first blows weren’t square. Keep the first few blows straight down before you start the angled ones.
  • The shank bends or kinks. The point may be too long and thin for its length, or it may still be soft and hot where it hangs below the header. A slightly stouter taper usually helps.
  • The tip is burned or crumbly. The point overheated in the fire. Thin sections heat very quickly, so pull the bar sooner or keep the tip out of the hottest part of the fire.
  • The head is too small or too big. Adjust the length of stub you leave above the cut. That’s the main control on head size.
  • Folds at the point. Hammering a tip that has bent over can fold metal into itself. If you see a fold, cut it off and redraw the point instead of hammering it flat.

Nail Head Styles

The rose head is the best known, but blacksmiths have made many others for different jobs:

  • Rose head: faceted and domed, a general-purpose head.
  • Clout or flat head: a broad, flat head for holding thin material such as sheet or leather.
  • T-head and L-head: narrow heads used where a nail needed to sit flush or nearly invisible, for example in flooring.
  • Decorative heads: large, shaped heads for studding doors and hardware. Some medieval nail heads were quite elaborate.

The same upsetting skill applies to forming rivet heads. If you plan to join pieces, our guide to blacksmith riveting techniques builds on it.

What to Do With Your Nails

Hand-forged nails don’t have to end up in a scrap bucket. Smiths use them for:

  • Practice and warm-ups before a session of other work.
  • Decorative pieces, such as studding a door, a box or a picture frame.
  • Restoration work where machine-made nails would look out of place, though period-correct restoration often has its own requirements.
  • Demonstrations, where nail making is a classic way to show the public how a smith works.

For the history side of the craft, see when they stopped using iron nails, and how medieval forges got hot enough to forge them.

Do Blacksmiths Still Make Nails for a Living?

Not in any meaningful numbers. Nail making was once a huge trade, often done as low-paid piecework. Machine-made cut nails and then wire nails replaced it during the nineteenth and early twentieth centuries. Today, hand-forged nails are a small specialty product for restoration, reproduction and decorative work. Nail making survives mainly as a skill exercise and a demonstration piece. If you want to understand the basic hammer techniques behind it, see How do you forge metal?.

The complete guide to projects

Blacksmith Project Plans for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →