Projects

How do you forge metal?

To forge metal, you heat it until it's soft, shape it with hammer blows, then reheat and repeat. Here are the core techniques, temperatures and safety basics.

On this page
  1. The Short Answer
  2. What Forging Actually Does to Metal
  3. What You Need to Forge Metal
  4. Step 1: Heat the Metal to Forging Temperature
  5. Step 2: Move the Metal With the Core Techniques
  6. Step 3: Work in Heats
  7. Step 4: Finish and Cool the Piece
  8. Hand Forging vs Industrial Forging
  9. Safety Basics
  10. A Good First Exercise

The Short Answer

To forge metal, you heat it in a forge until it’s hot enough to be soft and workable. For steel, that’s usually a bright orange to yellow. Then you shape it on an anvil with a hammer and other tools. Steel cools quickly, so you work in short bursts called heats, putting it back in the fire whenever it starts to dim. When the shape is done, you clean the piece up, let it cool, and apply a finish. Tools and blades made from higher-carbon steel also need heat treatment.

Everything else in blacksmithing is a refinement of that cycle: heat, hammer, reheat, repeat.

What Forging Actually Does to Metal

Forging shapes metal while it stays solid. Heat makes iron and steel much softer, so the hammer can push the metal around. It can be lengthened, thickened, bent or spread, and it stays in its new shape. The metal doesn’t melt and you don’t pour it into a mold. That’s the difference between forging and casting.

Because you’re moving metal rather than removing it, the volume stays roughly the same, apart from a little lost as scale (the dark oxide flakes that form on hot steel). If a bar gets longer in one place, it gets thinner there. If it gets thicker, it gets shorter. Keeping that in mind makes forging much more predictable.

What You Need to Forge Metal

  • A forge. Coal, charcoal and propane forges are the common choices for hobbyists. Induction heaters and electric kilns are also used.
  • An anvil, or a solid, heavy block of steel as a substitute. Mass and a flat, hard face matter more than shape.
  • A hammer you can control. A cross-peen or rounding hammer of moderate weight is a common starting point.
  • Tongs that fit the stock you’re using, unless you’re working off the end of a long bar.
  • A vise, ideally a leg vise, for bending and twisting.
  • Steel. New hot-rolled mild steel is the usual beginner material.
  • Safety gear: safety glasses, natural-fiber clothing, hearing protection, and good ventilation.

Step 1: Heat the Metal to Forging Temperature

Steel is easiest to forge at a bright orange to yellow heat. For mild steel, that’s roughly 1,800–2,200°F (about 980–1,200°C). Smiths judge it by color rather than measuring it, and colors look different in bright light and in shade. Most people find it easier to work out of direct sunlight.

Two things to avoid:

  • Overheating. If steel throws off bright, crackling sparks in the fire, it’s starting to burn. Burned steel is damaged and usually has to be cut off. Thin sections and tips burn fastest.
  • Working too cold. Once steel drops to a dull red, it gets much harder to move. Heavy hammering below that can cause cracks or folds, and it wears out your arm. Mild steel can be bent cold with care, but hammering it in the blue heat range, which is a dark, barely visible heat, is best avoided because the steel is less ductile there.

Heat the part you’re working on, not the whole bar. Heating only where you plan to work means the metal moves where you want it and nowhere else.

Step 2: Move the Metal With the Core Techniques

Almost every blacksmith project is built from a small set of basic operations.

Drawing Out

Drawing out makes a bar longer and thinner. You hammer the hot section on one face, rotate the bar 90 degrees, and hammer again, so it stays square. Using the hammer’s cross-peen, or working over the anvil’s horn, pushes metal along the length faster. You then smooth the surface with the flat face. Tapers and points are drawn out the same way, with the bar held at a slight angle.

Upsetting

Upsetting is the opposite: it makes a section shorter and thicker. You heat just the area to be thickened, then drive the bar’s end into the anvil, or hit the end with the hammer, so the hot section bulges. It’s slower than drawing out. Nail heads and rivet heads are formed this way.

Bending and Scrolling

Hot steel bends easily over the anvil’s horn, over the edge of the face, or in a vise. Scrolls are curls on the end of a bar. They start with a small bend at the tapered tip, then get rolled back on themselves. Controlling where a bend happens is mostly a matter of heating only that spot.

Twisting

Square or flat bar can be twisted for decoration. Heat a section evenly, clamp one end in a vise, and turn the other end with a wrench or twisting tool. Even heat gives an even twist.

Punching and Drifting

A punch drives a hole through hot steel, usually from both sides, finishing over a hole in the anvil. A drift is a tapered tool driven through the hole to enlarge and shape it. Unlike drilling, punching pushes material aside rather than removing it, so the area around the hole swells slightly.

Cutting

Hot steel can be cut with a hot chisel or a hardy, a cutting tool that sits in the anvil’s square hardy hole. Smiths often cut most of the way through, then snap or break the piece off.

Forge Welding

Forge welding joins two pieces of iron or steel by heating them close to white heat and hammering them together. Flux is often used to keep the surfaces clean. It’s one of the more demanding traditional skills, and most beginners learn it after the basics are comfortable.

Step 3: Work in Heats

A “heat” is one trip from the fire to the anvil and back. Steel loses its working heat surprisingly fast, especially thin stock, so plan each heat:

  1. Know what you’re going to do before you pull the bar out.
  2. Move quickly from fire to anvil.
  3. Do the most important blows first, while the metal is hottest.
  4. Put it back in the fire as soon as it dims, instead of chasing the last few blows.

Many smiths settle into a rhythm, and some tap the hammer lightly on the anvil between blows. If you’ve noticed this, see why blacksmiths double tap the anvil.

Step 4: Finish and Cool the Piece

For decorative mild-steel work, finishing is usually simple. Wire brush the scale off while the piece is still warm. Then apply beeswax or oil while it’s warm, or paint it once it’s cool. Mild steel can be left to air cool or cooled in water. Quenching mild steel doesn’t meaningfully harden it, and it doesn’t “set” the shape. The shape is set by the forging itself.

Higher-carbon steels behave differently. Tools such as chisels and punches, springs and knives need heat treatment to get useful hardness and toughness. That means hardening the steel by heating it and quenching it in a suitable medium, then tempering it at a lower temperature to reduce brittleness. The right temperatures and quench depend on the specific steel, so look them up for the steel you’re using. Don’t quench unknown steel casually, because some steels can crack.

Hand Forging vs Industrial Forging

The same principles apply at industrial scale, with machines in place of the arm:

  • Open-die forging shapes metal between flat or simple dies, like an anvil and a power hammer.
  • Closed-die (drop) forging hammers or presses hot metal into shaped dies to make many identical parts.
  • Press forging uses slow, heavy pressure instead of impact.
  • Cold forging shapes metal at or near room temperature, typically for small parts such as bolts.

Hand forging is slower, but it allows one-off shapes, decorative work and a lot of control. That’s why the craft survives alongside industry. Hand forging has a long history: see how medieval forges got hot enough for how smiths managed it with charcoal and bellows.

Safety Basics

  • Wear safety glasses at all times around the anvil, grinder and wire brush.
  • Wear natural-fiber clothing and closed leather shoes. Keep loose hair and clothing away from the fire.
  • Ventilate well. All fuel-burning forges produce carbon monoxide.
  • Treat every piece of steel as hot until you’ve checked it. Black-looking steel can still burn you badly.
  • Never forge galvanized or coated steel, because the fumes are harmful.
  • Keep water and a fire extinguisher close by.

A Good First Exercise

The best way to learn forging is to make something small that uses several techniques. An S hook uses tapering, scrolling and bending. Forging nails adds cutting and upsetting. From there, a forged leaf, a bottle opener and a twisted fire poker build the rest of the basic skills. Once you can make parts, riveting lets you join them. For the full progression, see our blacksmith project plans for beginners.

The complete guide to projects

Blacksmith Project Plans for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →