Projects

Blacksmith Project Plans for Beginners

Beginner blacksmith project plans with stock sizes, tools and techniques for each build, plus a simple method for working out stock length for your own designs.

On this page
  1. What a Useful Project Plan Includes
  2. Basic Setup and Safety Before You Start
  3. Choosing Steel for Beginner Projects
  4. Beginner Project Plans in a Sensible Order
  5. How to Work Out Stock Length for Your Own Plans
  6. Where to Go After the First Projects
  7. Common Questions

A good project plan does more than show a finished object. It tells you what steel to cut, roughly how long it should be, which tools you’ll need, and which skills the build will teach you. This guide puts beginner blacksmithing projects in a sensible order. Each one builds on the one before it, and each links to a full step-by-step guide. Near the end there’s a simple way to work out stock length, so you can start drawing up your own plans.

What a Useful Project Plan Includes

Most blacksmith plans you find online are a photo and a sentence. A plan you can work from at the anvil usually covers:

  • Material: the type of steel and its cross-section, for example 1/4” square mild steel.
  • Starting length: how much bar to cut, or whether to work off the end of a long bar and cut the piece off at the end.
  • Tools: forge, anvil, hammer, tongs, and anything special such as a vise, punch, drift, nail header or twisting wrench.
  • Techniques: the core moves involved, such as drawing out, scrolling, twisting, punching or upsetting.
  • Sequence: the order of operations. This matters more than people expect, because some steps make later ones awkward or impossible.
  • Finish: wax, oil, paint or a heat finish, depending on where the piece will live.

If a plan leaves out the stock size or the sequence, you can usually work those out from a photo. That gets easier with practice, and the stock-length section below helps.

Basic Setup and Safety Before You Start

Every project here can be done with a basic setup: a coal, charcoal or propane forge, an anvil or solid anvil substitute, a cross-peen or rounding hammer of moderate weight, one or two pairs of tongs, a bucket of water and a wire brush. A vise isn’t strictly required for most of these builds, but it makes twisting and bending much easier.

Treat safety gear as part of the setup:

  • Safety glasses whenever you’re hammering, grinding or wire brushing.
  • Natural-fiber clothing such as cotton, wool or denim, since synthetics can melt onto skin. A leather apron is also useful.
  • Hearing protection, because hammer and anvil noise adds up over a session.
  • Good ventilation. Coal, charcoal and propane forges all produce combustion gases, including carbon monoxide, so don’t run a forge in a closed space.
  • A fire extinguisher nearby, and a work area cleared of anything flammable.

Don’t forge galvanized steel. The zinc coating gives off fumes when heated that can make you ill. If you don’t know whether a piece of scrap is coated, leave it out.

Choosing Steel for Beginner Projects

For almost everything on this page, use new hot-rolled mild steel from a steel supplier. It’s inexpensive, consistent, and forgiving of mistakes. The common beginner sizes are:

  • 1/4” square or round: S hooks, nails, small scrolls, rivets and light hooks.
  • 3/8” square: leaves, bottle openers, fire pokers and wall hooks.
  • 1/2” square: heavier hooks and tools, once you’re comfortable moving metal.
  • Thin sheet (around 18–20 gauge): rose petals and other sheet work.

Scrap such as rebar, old bolts or leaf springs can be fun to experiment with later. But scrap varies a lot in carbon content and may carry coatings, and both make results less predictable. Learn how mild steel behaves first, then you’ll be able to tell when something else acts differently.

Beginner Project Plans in a Sensible Order

The table below is a starting point, not a rule. Stock sizes and lengths are typical choices, and many smiths use something slightly different.

Project Typical stock Main techniques Difficulty
S hook 1/4” square or round, about 6–8” Tapering, scrolling, bending First project
Forged nails 1/4” square, worked off a long bar Tapering, cutting, upsetting a head First project
Forged leaf 3/8” square, worked off a long bar Shouldering, spreading, veining Early
Bottle opener 3/8” square or small flat bar Flattening, punching, drifting Early
Fire poker with twist 3/8” square, about 32–36” Long tapers, scrolls, twisting Early to intermediate
Riveted pieces Flat bar plus mild steel rivets Drilling or punching, hot riveting Intermediate
Metal rose Thin sheet plus 1/4” round rod Sheet shaping, tenons, assembly Intermediate

S Hook

The S hook is the classic first project for good reason. In one small piece you practice a square taper, a scroll at each end and two controlled bends. You’ll also learn to keep everything in one plane. Start with 1/4” stock and finish with wax. The full walkthrough is in How to Forge an S Hook.

Forged Nails

Nails are tiny, but they teach a lot: a clean four-sided point, cutting partway through the bar, and upsetting a head in a nail header. Smiths often forge a batch of nails to warm up. The guide to forging nails covers rose-head nails and nail headers. If you’re curious why hand-made nails disappeared, see when they stopped using iron nails.

Forged Leaf

A leaf takes you from pure line (tapers and scrolls) to shape. You’ll set a shoulder, spread the metal with the cross-peen, and chisel in veins. Leaves turn up on hooks, pokers, key rings and decorative work, so they’re worth practicing until they come out reliably. See How to Forge a Leaf Step by Step.

Bottle Opener

A punched-and-drifted bottle opener is often the first project where you make a hole in hot steel. It also has a clear test: it either opens a bottle or it doesn’t. The handle is a good place to practice a twist or a scroll. See How to Forge a Bottle Opener.

Fire Poker with a Twisted Handle

A poker brings together several skills on a longer bar: a handle loop, a decorative twist, and a working end with a point or hook. Heating a long section evenly for the twist is the main new challenge. Follow the fire poker plan for stock length and twisting tips.

Riveted Pieces

Once you can make individual parts, you’ll want to join them. Riveting is one of the oldest ways to do that, and it doesn’t need a welder. Good first riveted projects include a simple bracket, a pair of hinged straps or a small decorative panel. Read blacksmith riveting techniques before you start.

Metal Rose

A forged rose is a popular gift piece. It combines sheet work with a forged stem, and often uses a riveted or peened tenon to hold the petals on. It takes patience with heat, because thin sheet heats very fast. See How to Forge a Metal Rose.

How to Work Out Stock Length for Your Own Plans

When you want to make something no plan covers, the hardest question is usually how much bar to start with. Two ideas get you most of the way.

Measuring Curves Along the Centerline

For anything bent, such as hooks, scrolls and rings, measure along the centerline of the bar in your drawing, not the inside or outside edge. A practical method is to draw the shape full size and lay a piece of wire or string along it. Then straighten the wire and measure it. For a ring, the centerline length is the ring’s centerline diameter multiplied by pi (about 3.14).

Drawing Down and Tapers: Volume Stays the Same

When you forge steel you move it around, but you don’t add or remove much of it (a little is lost as scale). So the volume stays roughly the same, and you can use that to estimate length:

  • Drawing down a bar: if you draw 3/8” square down to 1/4” square, the cross-section area falls from about 0.141 to 0.0625 square inches. That’s a ratio of 2.25, so 1” of 3/8” bar becomes about 2.25” of 1/4” bar.
  • Drawing a point: a straight four-sided taper to a point is close to a pyramid, which has one third the volume of a block of the same base and length. So a 3” pointed taper takes roughly 1” of the original bar.

Hand-forged shapes are never perfect, so treat these numbers as a starting estimate. Leave a little extra length when you can, or work off the end of a long bar and cut the piece free at the end.

Keep a Project Notebook

The most reliable plans are the ones you write yourself. Each time you make something, note the stock size, the starting length, the finished size and anything you’d change. After a few builds your notes will be more accurate than any general rule, because they reflect your own hammer, forge and habits.

Where to Go After the First Projects

Once these projects feel comfortable, common next steps include:

  • Tools for your own shop: tongs, punches, chisels and drifts. Making your own tools teaches you a lot about heat control. Tool steels also bring in hardening and tempering.
  • Hardware: hinges, latches, hooks and brackets, which often need joinery such as rivets or collars.
  • Decorative ironwork: scrolled panels, candle holders, small gates and sculpture. Our guide to blacksmith art and design covers the design side.
  • Bladesmithing: many blacksmiths do make knives, but bladesmithing is a specialty of its own. It uses higher-carbon steel and needs careful heat treatment.

If you’d like a broader overview of the basic moves behind all of these, see How do you forge metal?.

Common Questions

What do blacksmiths make?

Historically, blacksmiths made and repaired almost everything iron a community needed: tools, nails, hinges, hardware, cooking gear, farm equipment and parts for carts and wagons. Today most hobby and professional smiths make decorative and architectural ironwork, household items such as hooks and fireplace tools, their own tools, and sometimes knives. Some focus on restoration or historical reproduction. For a longer list, see what blacksmiths craft.

Is forging a cheap hobby?

It can start fairly cheap, but it isn’t free. A basic setup with a small propane or homemade forge, a used or improvised anvil, a hammer and a pair of tongs can often be put together for a few hundred dollars, especially if you build some of it yourself. Mild steel for practice is inexpensive. Costs go up quickly with a good-quality anvil, a power hammer or a well-equipped shop, so most people upgrade slowly as they learn what they need. Classes and local blacksmithing groups are often a cheaper way to try the craft before buying much equipment.

What’s the difference between a blacksmith and a forge?

A blacksmith is a person who works iron and steel. A forge is the hearth or furnace that heats the metal. The word “forge” is also used for the workshop itself, also called a smithy, and as a verb for shaping hot metal with force. Interest in old forges sometimes leads to the question of how medieval forges got hot enough, which comes down to charcoal and a steady blast of air. If you’ve ever wondered about the rhythm you hear in a working smithy, see why blacksmiths double tap the anvil.

Keep exploring

Guides from other topics

All topics →