Projects

How to Forge an S Hook: A First Blacksmithing Project

Step-by-step guide to forging an S hook from 1/4" mild steel: tapering, scrolling the tips, bending the hooks, truing up, finishing and fixing common mistakes.

On this page
  1. Why the S Hook Is the Classic First Project
  2. What You’ll Need
  3. Step 1: Taper the First End
  4. Step 2: Scroll the Tip
  5. Step 3: Taper and Scroll the Other End
  6. Step 4 (Optional): Add a Twist
  7. Step 5: Bend the Two Hooks
  8. Step 6: True It Up
  9. Step 7: Finish the Hook
  10. Troubleshooting
  11. Variations to Try Next

The S hook is the project most blacksmithing teachers start with. It’s small, cheap and useful, and in one short piece of steel it teaches three basic skills: drawing a taper, rolling a scroll and making a controlled bend. Make a few and you’ll notice real progress from the first to the last.

Why the S Hook Is the Classic First Project

  • It uses very little steel, so mistakes cost almost nothing.
  • It practices core skills: tapering, scrolling, bending and keeping work flat and in line.
  • It shows mistakes clearly. An uneven taper or an off-plane bend is easy to see, so you learn fast.
  • It’s genuinely useful. S hooks hang pots, tools, plants and bags.

If you’d like to see where it sits among other first builds, see our blacksmith project plans for beginners.

What You’ll Need

  • Stock: 1/4” square or round mild steel. A piece about 6 to 8 inches long makes a hook roughly 3 to 4 inches tall, depending on how long your tapers are and how big your curls and hooks are. You can also work off the end of a longer bar and cut the hook free when one end is done.
  • Hammer: a cross-peen or rounding hammer you can control comfortably.
  • Anvil with a horn, or a substitute with a rounded edge or bending form.
  • Tongs that hold 1/4” stock securely, for when the piece gets too short to hold by hand.
  • A vise (optional, but handy for the twist and for adjustments).
  • Wire brush and finish: beeswax, paste wax or oil.
  • Safety glasses and natural-fiber clothing.

Step 1: Taper the First End

Heat about the last 2 inches of the bar to a bright orange. At the anvil, hold the bar at a slight angle to the face, with the end lower, and hammer near the tip. Hit once or twice, rotate the bar 90 degrees, and hit again. Keep rotating back and forth so all four faces get worked evenly.

Aim for a smooth, square taper about 1 1/2 to 2 inches long. It should come down to a fine but not needle-sharp end. Check it often by sighting down the bar. If the cross-section starts to look like a diamond rather than a square, see the troubleshooting section below.

If you’re using round stock, taper it square first, then knock the corners down to an octagon and roll it round.

Step 2: Scroll the Tip

A small curl on each end makes the hook look finished and keeps it from snagging.

  1. Reheat the taper to orange.
  2. Hold the bar so the very tip hangs just over the far edge of the anvil face, then tap it down to bend the last 1/4 inch or so over the edge.
  3. Turn the bar so the bent tip points up, and lay it at an angle on the face. Tap lightly on the tip so it rolls back over on itself into a small curl.
  4. Keep rolling the curl by tapping on its outside edge while you feed the bar forward, until the scroll is the size you want.

Use light blows. Scrolls are easy to flatten or crush. Stop when the scroll looks round and tight.

Step 3: Taper and Scroll the Other End

Hold the finished end in your tongs, or by hand if the bar is long enough to stay cool where you grip it. Then repeat steps 1 and 2 on the other end. Try to match the length of the first taper and the size of the first scroll.

Turn this second scroll the opposite way from the first. On a finished S hook, the curls at each end point away from each other, so the two hooks curve in opposite directions. Laying the bar flat and checking which way each scroll faces before you bend will save confusion later.

Step 4 (Optional): Add a Twist

With square stock you can add a twist to the middle of the bar for decoration:

  1. Heat the middle section evenly, an inch or two long, to a bright orange.
  2. Clamp one end of the hot section in the vise, at the edge of the heat.
  3. Grip the other end of the hot section with tongs or a wrench and turn steadily. One full turn is plenty on a small hook.
  4. Sight down the bar and straighten it if needed with light blows on a wooden block or with your hands while it’s still hot.

The key is even heat. A section that’s hotter in one spot will twist more there.

Step 5: Bend the Two Hooks

  1. Heat one end, including the scroll and about 2 inches behind it, to orange.
  2. Lay the hot section over the anvil horn, with the scroll pointing up and away from you.
  3. Tap the bar down around the horn to form a curve, working back from the scroll toward the middle of the bar. Move the bar along the horn to get a smooth curve, not a sharp kink.
  4. Repeat on the other end, bending the opposite way to make the “S”.

Size each hook for its job. A hook that will hang over a rail or rod needs an opening slightly bigger than the rail. Many S hooks have one hook a little larger than the other.

Step 6: True It Up

Lay the hook flat on the anvil face. Ideally the whole thing lies flat in one plane. If one hook is twisted or lifted, reheat it and tap it flat gently. Use light blows on the curve only, so you don’t flatten the stock out of shape.

Check that the scrolls, curves and middle all line up when you look at the hook edge-on. Adjust the hook openings with tongs or a bending fork if needed. This last bit of truing is what makes a hook look crisp instead of homemade.

Step 7: Finish the Hook

While the hook is still warm but no longer glowing, scrub the scale off with a wire brush. Then:

  • Indoors: rub on beeswax or paste wax while the steel is warm enough to melt it, then buff it with a rag once it’s cool. This gives a dark, low-sheen finish.
  • Outdoors: paint will hold up better than wax. Let the hook cool fully, clean it, then apply a primer and paint suitable for metal.

Always assume steel is hot until you’ve checked it. A hook that has stopped glowing can still burn you badly.

Troubleshooting

  • The taper is diamond-shaped instead of square. This usually comes from hitting at a slight angle or rotating unevenly. Hit the bar on the long corners of the diamond to bring it back to square, then continue rotating 90 degrees at a time.
  • The tip folded over or split. You probably hammered the tip too cold or too thin. Cut off the damaged section and draw a fresh taper.
  • The scroll is lumpy or oval. Start the curl smaller and roll it with lighter, more frequent blows on the outside of the curl.
  • The hooks don’t line up. One end got twisted during bending. Reheat it and twist it back into line with tongs, then flatten it on the face.
  • The bend kinked instead of curving. Move the bar along the horn as you bend, and heat a longer section.

Variations to Try Next

  • A leaf end: forge a small leaf on one end instead of a scroll. See How to Forge a Leaf Step by Step.
  • Heavier hooks: 3/8” stock makes sturdier hooks for pots or tools. They need longer heats.
  • Wall hooks: flatten one end and punch or drill a hole so it can be screwed to a wall.
  • Longer projects: once tapers, scrolls and twists feel natural, the twisted-handle fire poker and the forged bottle opener are good next steps.

For the basic forging techniques behind all of this, see How do you forge metal?.

The complete guide to projects

Blacksmith Project Plans for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →