A fire poker is a natural next step after small hooks. It uses the same tapers and scrolls on a longer bar and adds a decorative twist. It also gives you something genuinely useful at the end. This guide covers a classic design: a looped handle, a twisted section below it, and a pointed working end with a hook for dragging logs.
The Plan at a Glance
| Item | Typical choice |
|---|---|
| Stock | 3/8” square mild steel |
| Starting length | About 32–36” |
| Finished length | Roughly 28–32”, depending on the loop and tapers |
| Main techniques | Tapering, scrolling, bending, twisting, straightening |
| Finish | Wax or oil on the handle, or a high-temperature paint |
A longer poker keeps your hand further from the fire. A shorter one is easier to forge and store. If you’re unsure, a finished length around 30 inches suits most household fireplaces and wood stoves.
What You’ll Need
- Stock: 3/8” square mild steel, about 32–36” long. Square stock gives a crisp twist. Round stock won’t show one.
- Forge that can heat a section several inches long fairly evenly. Some small gas forges have a short hot zone, so you may need to move the bar back and forth.
- Hammer and anvil with a horn.
- Vise, ideally a leg vise, for twisting.
- Twisting tool: an adjustable wrench, a monkey wrench or a purpose-made twisting bar.
- Tongs for the hot end if needed. You’ll mostly hold the cool end of the bar by hand.
- Wooden block or mallet for straightening.
- Wire brush and finish.
- Safety glasses and natural-fiber clothing.
Step 1: Taper the Handle End
Heat about the last 3 inches of one end to a bright orange. Draw out a square taper about 2 to 3 inches long, rotating 90 degrees between blows to keep it square. Finish with a fine end, which will be rolled into a scroll. The taper makes the loop look lighter and more graceful than a blunt bar end.
Step 2: Form the Handle Loop
- Scroll the tip. Bend the very tip over the edge of the anvil, then roll it back on itself into a small scroll, as you would on an S hook.
- Bend the loop. Heat the section behind the scroll and bend it over the anvil horn into a loop. Make it big enough to fit a few fingers or to hang from a hook, often about 1 1/2 to 2 inches across inside.
- Close it up. Bring the loop around so the scroll sits neatly against the shaft. Adjust with light taps and tongs until the loop is centered over the shaft and lies flat.
Other handle styles include an open “shepherd’s crook” curve, a simple ring, or a leaf end. A leaf makes a pleasant, rounded grip. See How to Forge a Leaf Step by Step.
Step 3: Twist the Handle Section
Decide where the twist will go. A twist of about 4 to 6 inches starting an inch or two below the loop is common. Mark both ends with soapstone or a light center-punch dot.
- Heat evenly. Bring the whole section to an even bright orange. Even heat is the most important part of a good twist, because hotter spots twist more than cooler ones.
- Clamp it. Put the bar in the vise with the jaws at one end of the heated zone.
- Twist. Put the wrench on the other end of the heated zone and turn it steadily. Count your turns. One to three full turns is typical for a section of this length, depending on how tight you want it.
- Keep it tidy. If the twist starts to creep beyond your marks, you can cool the ends of the zone briefly with a little water to help pin the twist where you want it.
Decide which direction to twist and keep to it. If you make a matching set of fire tools, twist them all the same way.
Step 4: Straighten the Twist
Twisting often bends the bar slightly. While it’s still hot, sight down the bar. Straighten it by tapping on a wooden block with a wooden or rawhide mallet, or by gently bending by hand against the anvil. Avoid heavy blows with a steel hammer on the twist, because they’ll flatten its crisp edges.
Step 5: Forge the Working End
Move to the other end of the bar. A practical working end has a point for pushing logs and a hook for pulling them. One common, beginner-friendly approach:
- Draw a long taper. Heat the end and draw a square taper about 4 to 5 inches long down to a blunt point.
- Form the hook. Reheat and bend the last 1 1/2 to 2 inches back on itself over the horn or the anvil edge. The hook should angle back toward the handle and stand out from the shaft. The bend becomes the pushing tip, and the end becomes the pulling hook.
- Tidy it up. Adjust the hook so it lies in line with the handle loop, not twisted off to one side.
Alternatives:
- A simple point: skip the hook and leave a straight, blunt taper. It’s the easiest option and still works well.
- A separate spur: make a side spike by splitting the bar or forge welding on a short piece. This is a more advanced technique, best left until you’ve done a few pokers.
Keep the tip reasonably blunt. A sharp point is unnecessary in a fireplace and easy to catch on things.
Step 6: Final Straightening and Truing
With all the forging done, lay the poker on the anvil or a flat surface and check that:
- the shaft is straight along its length
- the handle loop, twist and hook are all in line
- nothing is twisted out of plane
Make small corrections at a low orange heat, using light blows or bending by hand against the anvil.
Step 7: Finish the Poker
The working end will get hot in the fire and scale up over time whatever you put on it. So the finish matters most on the handle and shaft:
- Wax or oil: wire brush the poker while it’s warm, then rub beeswax or paste wax onto the handle and shaft while it’s warm enough to melt the wax. It’s simple and traditional, but near the fire it will need renewing now and then.
- High-temperature paint: stove or grill paint rated for high heat holds up better on parts that get hot. Follow the manufacturer’s directions for application and curing.
Upgrades and Variations
- Collars: wrap a short collar around the shaft below the twist for a decorative accent.
- Matching fire tools: use the same twist and handle style for a shovel, brush and tongs. Rivets are a common way to join the parts. See blacksmith riveting techniques.
- A hanging stand: forge a simple stand with hooks for your set of tools.
- Different twists: try a tighter twist, or two short twists with a plain section between them.
Troubleshooting
- The twist is uneven. Your heat wasn’t even across the section. Take more time in the fire, move the bar back and forth through the hot zone, and check the color along the whole section before twisting.
- The twist spread past your marks. The heated zone was longer than you intended. Heat more precisely, or cool the ends of the zone before twisting.
- The bar bent during twisting. That’s normal to some degree. Straighten it while hot with a wooden mallet on a wooden block.
- The loop is off-center. Reheat it and adjust with tongs, using the horn as a form.
- The hook won’t sit in line. Reheat the bend and use tongs to twist the hook into line with the handle.
Safety With Long Bars
A 3-foot bar is easy to lose track of. Keep these points in mind, along with the general rules in our beginner safety guide:
- Both ends can be hot. Heat travels along the bar, and the end you’ve just worked may still be very hot even if it isn’t glowing.
- Watch your swing. Turning a long bar can swing the far end into people, walls or things nearby. Keep your work area clear.
- Rest the bar safely. Don’t lean a hot bar where someone might grab it or brush against it. A rack or a clear spot on the anvil stand is better.
- Wear safety glasses for all of it, including the wire brushing.
If this is your first longer project, you might warm up with an S hook or a forged bottle opener first. For more ideas, see our blacksmith project plans for beginners, and for the techniques behind them, How do you forge metal?.