Projects

How to Forge a Leaf Step by Step

Learn to forge a decorative leaf from 3/8" mild steel: point, shoulder, stem, spreading the blade, veining with a chisel, shaping and finishing with wax.

On this page
  1. What You’ll Need
  2. Step 1: Forge the Leaf Tip
  3. Step 2: Set the Shoulder
  4. Step 3: Draw Out the Stem
  5. Step 4: Spread the Leaf Blade
  6. Step 5: Add the Veins
  7. Step 6: Give the Leaf Some Life
  8. Step 7: Finish the Stem
  9. Finishing the Leaf
  10. Leaf Shapes to Try
  11. Common Problems
  12. What to Make With Forged Leaves

A forged leaf is one of the most useful decorative elements in blacksmithing. Once you can make one reliably, you can add it to hooks, pokers, key rings, handles, railings and roses. It’s also a great step up from tapers and scrolls, because you start shaping metal in width as well as length. This guide walks through one common method using 3/8” square mild steel.

What You’ll Need

  • Stock: 3/8” square mild steel. Working off the end of a long bar is easiest, since the bar acts as your handle. A leaf with a short stem might use around 3 to 4 inches of bar, and longer stems use more.
  • Hammer: a cross-peen is very helpful for spreading the leaf. A rounding hammer also works.
  • Anvil with a crisp edge and a slightly rounded edge, or a fuller, for setting the shoulder.
  • A dull chisel or veining tool for the veins. A chisel with a rounded, blunt edge works better than a sharp one.
  • Vise (optional) for holding the leaf while you vein or shape it.
  • Wire brush and beeswax or another finish.
  • Safety glasses and natural-fiber clothing.

Step 1: Forge the Leaf Tip

Heat the end of the bar to a bright orange or yellow. Draw a short, square taper on the very end, about an inch or so long. This becomes the leaf’s tip. Don’t make it too long or fine yet, because the spreading step will lengthen and thin it further.

Step 2: Set the Shoulder

The shoulder is where the leaf ends and the stem begins. Measure back from the tip about the length of leaf you want. A leaf an inch and a half to two inches long is a good beginner size.

At a good heat, lay the bar across the anvil so the planned shoulder sits right at the edge. Strike half on and half off the edge. Half the hammer face lands on the bar over the anvil, and the other half overhangs. This necks the bar down behind the leaf. Rotate the bar 90 degrees between blows to keep it square.

Use a slightly rounded edge, or a fuller, rather than a dead-sharp corner. A sharp 90-degree step at the shoulder creates a weak point where cracks can start, and it looks harsh. A smooth, gently curved transition is stronger and looks more natural.

Step 3: Draw Out the Stem

Move behind the shoulder and draw out the stem. Bring it down to a thinner square, then knock off the corners to an octagon. Roll it on the anvil face with light blows until it’s round. How long you make the stem depends on what the leaf is for:

  • a short stem for a key ring or pendant
  • a longer, tapering stem that can be scrolled or attached to another piece

You can do this step later instead if you prefer to keep the full bar as a handle while you shape the leaf.

Step 4: Spread the Leaf Blade

Now flatten the leaf section. Lay it on the anvil face and hammer it down to a thinner plate. Then use the cross-peen to spread it sideways. With the peen running parallel to the length of the bar, strikes push metal out toward the edges and widen the leaf.

Work from the center line out toward each edge, flipping the leaf often so both sides spread evenly. Follow with the flat face to smooth the peen marks, or leave some for texture. Aim for a blade that’s thicker down the middle and thinner toward the edges. That looks more natural and leaves room for the vein.

Watch your heat closely. As the leaf gets thinner it heats much faster in the fire and cools much faster on the anvil. Pull it out as soon as it reaches color, and don’t let it sit in the hottest part of the fire, or the edges will burn.

Step 5: Add the Veins

Reheat the leaf to an orange heat. Hold it on the anvil face, or in a vise, and use a dull chisel to press in a central vein from the stem toward the tip. Use firm but controlled blows. You want a clear groove, not a cut through the leaf.

Side veins are optional. If you add them, angle them out from the central vein toward the tip, like a real leaf. Short, light strikes work best. Some smiths use the edge of the cross-peen for softer, wider veins.

If you vein on the anvil face, the back of the leaf stays flat. If you vein over a slightly yielding surface, such as a wooden block or a lead block, the vein shows on both sides. But use lead only with care, because lead dust and fumes are toxic.

Step 6: Give the Leaf Some Life

A perfectly flat leaf can look stiff. With the leaf at a dull orange heat, try one or more of these:

  • Fold along the vein: set the leaf over the edge of the anvil or in the jaws of a vise and fold it slightly along the center line.
  • Curl the tip: use round-nose pliers or light taps to curl the tip up or to one side.
  • Ripple the edges: use pliers or the horn to put a gentle wave in the leaf’s edges.

Keep it subtle. A little movement goes a long way.

Step 7: Finish the Stem

If you worked off a long bar, cut the leaf free at the end of the stem with a hardy or hot cut, leaving enough stem for its purpose. Common stem finishes include:

  • a small loop or ring for a key ring or pendant
  • a tight scroll
  • a hook, so the leaf becomes a small wall hook
  • a long tapered stem to attach to a larger piece

Finishing the Leaf

While the leaf is still warm, scrub it with a wire brush to remove scale. A brass brush gives a softer, slightly golden tint on warm steel. Rub beeswax over it while it’s warm enough to melt the wax, then buff it once it’s cool. For outdoor pieces, a clear coat or paint will last longer.

Leaf Shapes to Try

  • Willow or narrow leaf: a long taper and only a little spreading. This is the easiest place to start.
  • Round leaf: spread more and shorten the leaf to get a broad, round blade.
  • Oak leaf: forge a broad leaf, then cut lobes into the edges with a chisel and soften them with a file or light hammer work.
  • Leaf on a stem: draw a long, tapering stem and leave it straight or gently curved for flower arrangements or roses.

Common Problems

  • The leaf cracked at the shoulder. The step was too sharp or was worked too cold. Use a rounded edge or a fuller, and reheat sooner.
  • The edges are ragged or burned. The thin edges overheated in the fire. Pull the leaf sooner and keep it out of the hottest spot.
  • The vein cut through. The chisel was too sharp or the blows too hard. Use a dull tool and lighter, controlled strikes.
  • The leaf is lopsided. One side was spread more than the other. Work from the center line out and alternate sides.
  • The leaf is too thick and clunky. Spread a little more, and thin the edges in particular.

What to Make With Forged Leaves

Leaves pair naturally with other beginner projects. Add one to the end of an S hook or a bottle opener handle. Put one on a fire poker, or attach a couple to the stem of a forged metal rose. For ideas on using leaves in larger decorative work, see blacksmith art and design, and for more starter builds, see our blacksmith project plans.

The complete guide to projects

Blacksmith Project Plans for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →