What a good anvil stand needs to do
An anvil works best when it sits solidly at the right height. A good stand:
- Holds the anvil at a comfortable working height
- Doesn’t rock, walk or bounce under heavy blows
- Keeps the anvil secured, so it can’t shift or tip
- Adds mass and stiffness beneath the anvil
- Ideally deadens some of the ring of a loud anvil
A well-mounted anvil feels more solid and efficient, which can matter as much as its weight. See how heavy a blacksmith anvil should be.
Getting the height right
The common starting point is to set the anvil face at about knuckle height:
- Stand straight in your usual work boots, arms relaxed at your sides.
- Measure from the floor to your knuckles (the middle knuckles of your loosely closed hand).
- Measure the height of your anvil from its base to the face.
- Subtract the anvil height from your knuckle height. That’s your stand height.
For example, with a knuckle height of 30 inches and an anvil 10 inches tall, the stand would be about 20 inches high.
Some smiths prefer the face slightly lower, which suits heavy hammering, or slightly higher, for fine work and bladesmithing. Knuckle height is a reasonable start. You can trim a wooden stand later, or add a shim, after you’ve tried it. If you find yourself bending over a lot or your shoulders ache, revisit the height.
Design 1: the tree stump
The traditional stand is a section of tree trunk, set end grain up.
- Choose a sound hardwood section if you can, free of rot and large splits. It should be wider than the anvil’s feet for stability.
- Cut both ends square and parallel so the anvil sits level and the stump doesn’t rock. A chainsaw gets you close, and you can level the top with a plane or grinder flap disc.
- Remove the bark, which can harbour insects and moisture.
- Expect checking (cracks) as green wood dries. Small surface cracks are usually harmless. Some smiths seal the ends or bind the stump with steel bands to limit splitting.
- Keep it off damp ground if possible, for example on a paver or concrete, to slow rot.
A stump is cheap, solid and quiet, but it can be heavy and hard to source in the right size.
Design 2: laminated timber
If you can’t find a stump, you can build an equivalent from dimensional lumber:
- Cut lengths of timber (such as 4x4s, 6x6s or stacked 2x lumber) to your stand height.
- Stand them vertically in a bundle, so the end grain faces up, like a stump.
- Glue the faces together with construction adhesive or wood glue.
- Clamp and bolt the bundle with threaded rod running through it horizontally, or with heavy lag screws.
- Trim the top flat and, if you like, rout a shallow recess for the anvil’s base, which helps stop it shifting.
This is quieter than steel and doesn’t need welding. Use plain, untreated timber where possible. Pressure-treated wood contains preservatives, so avoid breathing its sawdust and don’t burn its offcuts in the forge.
Design 3: welded steel tripod
A steel stand is popular for its compact footprint, and three legs never rock, even on an uneven floor.
- Legs. Heavy-wall square or round tube, or angle iron, splayed outward for a wider footprint.
- Top. A steel plate or frame that matches the anvil’s base, with tabs or bolt holes for securing it.
- Feet. Flat pads on dirt, so the legs don’t sink, or bolt-down tabs on concrete.
- Fill. Packing hollow legs with dry sand adds weight and cuts down vibration and ring.
Splaying the legs out at a modest angle, often somewhere around 10 degrees, adds stability. This design does need welding skills and equipment. If you’re new to welding, get help from someone experienced, because a failed weld under a heavy anvil is dangerous.
Design 4: sand-filled box or drum
A sturdy box filled with sand is a simple design that’s excellent for noise:
- Build a strong box from thick plywood or timber, or use a heavy steel drum.
- Fill it with dry sand, packed down.
- Set the anvil on a timber block bedded into the top of the sand, or directly on the sand inside a frame.
The sand absorbs vibration and makes the setup very quiet. It’s heavy and hard to move once filled, and the anvil may need re-levelling occasionally as the sand settles.
Mounting the anvil to the stand
However you build the stand, secure the anvil so it can’t walk or tip:
- Chain and turnbuckles or lag bolts. Run a chain over the anvil’s feet and tension it to the stand with lag bolts or turnbuckles. This is common, cheap and effective.
- Steel brackets or straps. Bent steel bar or angle iron screwed to the stand and clamping over the feet.
- Bolts through the base, if your anvil has holes in its feet and the stand allows it.
- Staples or spikes driven into a wooden stand around the feet. This is traditional but less secure.
Check the fasteners from time to time, because hammering tends to loosen them.
Reducing anvil ring
Some anvils ring loudly enough to be uncomfortable, and that matters for your hearing and your neighbours. Ways to quiet them:
- Bed the anvil on a thin layer of silicone caulk or a similar compound, then let it cure before heavy use.
- Tighten the mounting. A firmly secured anvil generally rings less than a loose one.
- Wrap a chain around the waist of the anvil, or hang a strong magnet under the heel or horn.
- Fill steel stand legs with sand.
Wear hearing protection regardless. Even a quiet anvil is loud.
Adding tool storage
A stand is a handy place to keep tools, but don’t clutter the area around the anvil face:
- Hammer racks on the side of the stand
- Hooks or loops for tongs
- A holder for hardy tools, such as blocks with square holes
Keep anything stored on the stand below the face, and away from where hot work or scale will fall.
Floor and placement
- A solid floor matters. Concrete or firm, compacted ground both work. A springy wooden floor wastes energy.
- Position the anvil close to the forge, typically within a step or two, so the work doesn’t cool on the way.
- Leave room around it to swing a hammer and move long bars.
If you don’t have an anvil yet, these designs work just as well for an improvised anvil like a steel block. See poorboy blacksmith tools. For choosing the anvil itself, read our anvil review. For the rest of the setup, see our essential blacksmithing kit guide.