Anvils and Tools

Making a Steel Hand Stamp

How to make a steel hand stamp or touchmark: choosing tool steel, designing a mirror-image mark, cutting it, heat treating for hot or cold use, and stamping.

On this page
  1. What a hand stamp (touchmark) is
  2. Hot stamping vs cold stamping
  3. Choosing the steel
  4. Designing the mark
  5. Preparing the blank
  6. Cutting the design
  7. Testing the impression
  8. Heat treating
  9. Using your stamp
  10. Maintenance
  11. Buying instead of making

What a hand stamp (touchmark) is

A steel hand stamp is a short bar of hardened steel with a design raised on one end. When struck with a hammer, it presses that design into metal. Blacksmiths call a personal mark a touchmark or maker’s mark. It’s usually initials or a simple symbol, stamped into finished pieces so they can be identified.

Industry uses the same kind of tool for part numbers, welder identification and logos. Commercial makers will cut a custom stamp to order. Making your own is a rewarding project, though, and it uses skills you already practise at the forge: shaping, filing and heat treating.

Hot stamping vs cold stamping

Decide early how you’ll use the stamp, because it affects steel choice and heat treatment.

  • Hot stamping. The stamp is struck into steel at forging heat. This is the usual way blacksmiths apply touchmarks, because hot steel takes a crisp impression with a modest blow. The stamp itself gets heated by contact, so it needs steel that tolerates heat, and it’s typically tempered tougher rather than very hard.
  • Cold stamping. The stamp is struck into cold metal, such as a finished blade or soft metals like copper, brass or aluminium. Cold steel resists strongly, so the stamp needs a harder face, and fine detail is harder to transfer.

Many smiths make a stamp mainly for hot use. It’s more forgiving and gives a deeper mark.

Choosing the steel

You need a steel that can be hardened. Common choices:

  • Shock-resisting tool steels such as S7, often used for punches and stamps because they resist chipping.
  • Hot-work tool steels such as H13, made to keep their properties when heated, which suits frequent hot stamping.
  • Water- or oil-hardening tool steels such as W1, W2 or O1. These are widely available and easy to heat treat at home.
  • Salvaged high-carbon steel, such as coil springs, old punches or jackhammer bits. These can work, but the exact alloy is unknown, so test a piece first.

Each steel has its own recommended hardening and tempering routine. If you buy known tool steel, follow the supplier’s data sheet. Stock of roughly 3/4 inch to 1 inch (about 20 to 25 mm) round or square, cut to around 4 to 6 inches (about 100 to 150 mm) long, makes a comfortable stamp to hold and strike.

Designing the mark

A good touchmark is simple. Some guidelines:

  • Mirror the design. The stamp face must be the reverse of the mark you want to see. Letters especially need flipping.
  • Keep it bold. Thick lines and open shapes transfer far better than fine detail, especially into hot steel, which tends to flow and soften edges.
  • Keep it small. Touchmarks are commonly somewhere around 1/4 to 1/2 inch (about 6 to 12 mm) across. Smaller marks need less force to strike cleanly.
  • Give it a border, or don’t. A raised outline frames the mark but requires more metal to move. Many smiths leave it off.
  • Taper the sides. The raised parts of the design should have slightly sloped (drafted) sides, wider at the base. This makes them stronger and helps the stamp release cleanly.

Sketch the mark at full size, then mirror it before transferring it to the steel.

Preparing the blank

  1. Anneal the steel if it isn’t already soft. Heat it past non-magnetic and cool it slowly, buried in ash or vermiculite. Soft steel is far easier to cut.
  2. Square and flatten the working face with a file or grinder. A slight dome can help the stamp transfer evenly if your strikes aren’t perfectly square.
  3. Shape the struck end. Grind a chamfer around the top edge so it’s less likely to mushroom and chip later.
  4. Coat the face with layout fluid or a dark permanent marker, so scribed lines show clearly.
  5. Transfer the mirrored design. Scribe it by hand, or print it, stick it to the face and cut through it.

Cutting the design

You’re removing everything that isn’t the mark, leaving the design standing proud. Tools that work:

  • Needle files. Slow but controllable. They suit straight lines and corners.
  • A rotary tool with small burrs. Faster for clearing background areas. Keep a light touch, and wear eye protection and a dust mask.
  • Small chisels and gravers. Traditional and precise, with practice.
  • Hot work. Some smiths chisel or punch a simple design into a hot blank, though this is harder to control.

Work slowly and check often. The background only needs to be cut deep enough that it doesn’t touch the work when you stamp. For hot stamping, a millimetre or two of relief is often enough.

Testing the impression

Before heat treating, test the stamp by pressing or tapping it into modelling clay, soft wood or a scrap of soft metal like copper or aluminium. Look for:

  • Mirrored letters reading correctly in the impression
  • Even depth across the design
  • Fine areas that are filling in or not printing

Make corrections while the steel is still soft.

Heat treating

Exact temperatures depend on the steel, so follow the data sheet if you know the alloy. A general approach for simple carbon or oil-hardening steels:

  1. Harden the working end. Heat the lower part of the stamp evenly to just past non-magnetic, then quench in the medium the steel needs (oil for O1, water or brine for W1, and so on).
  2. Check that it hardened. A file should skate on the face.
  3. Temper. Polish the side so you can see oxide colours, then heat gently from the middle of the stamp so the colour runs toward the face.
    • For hot stamps, many smiths temper fairly tough, around a purple-to-blue colour. The stamp will see heat in use anyway.
    • For cold stamps, a harder temper, around straw to bronze, holds the detail better against cold metal.
  4. Draw the struck end softer than the face, toward blue or beyond, so it deforms rather than shattering when struck.

If a stamp chips in use, it’s probably too hard. If the design flattens, it’s too soft.

Using your stamp

  • Hot stamping. Bring the piece to a good forging heat and support it on the anvil face. Hold the stamp square and strike once, firmly. A second blow often doubles the image. Dip the stamp in water between uses, so it doesn’t heat up and lose its temper.
  • Cold stamping. Support the work on a solid surface, hold the stamp square and strike firmly with a suitably heavy hammer. One clean blow is better than several light ones.
  • Hold it safely. For hot work, use a stamp holder or tongs rather than holding the stamp close to the hot steel with bare fingers.
  • Use the right hammer. A mid-weight engineer’s or club hammer suits most stamps. Your best forging hammer face is worth keeping for forging. See our guide to blacksmith hammers.

Practise on scrap before you mark a finished piece.

Maintenance

  • Grind off any mushrooming on the struck end promptly. A mushroomed head can throw chips.
  • Keep the face clean of scale.
  • Store it dry to prevent rust in the fine detail.

Buying instead of making

If your design is intricate, or you need a crisp mark for cold stamping hardened steel, a commercially made custom stamp may be worth the cost. Many smiths end up with both: a homemade stamp for hot work and a bought one for finer cold marking.

The hardening and tempering steps here are the same skills used in making chisels from old files. For more on the kinds of pieces you might sign, see what do blacksmiths craft? and our beginner’s blacksmithing kit.

The complete guide to anvils and tools

Blacksmithing Tools of the Trade: The Beginner's Essential Kit
Read the guide

Keep exploring

Guides from other topics

All topics →