The “gas bottle forge” is one of the most popular homemade blacksmithing forges. Take a steel cylinder, line it with ceramic fiber wool, add one or two homemade burners, and you have a clean-burning forge that lights in seconds and reaches forging heat quickly. This guide covers the forge body, a simple venturi burner, and the gas plumbing that connects them.
If you’re still choosing a forge type, our beginner’s guide to building a blacksmith forge compares this build with coal, charcoal and brick designs.
What a gas bottle forge is
A gas bottle forge is a steel cylinder used as a shell. It’s often an old propane bottle, a disposable refrigerant or helium cylinder, or a short length of steel pipe. Inside it are:
- Insulation, usually ceramic fiber blanket
- A protective refractory coating over that insulation
- A hard floor that can take the abrasion and flux
- One or more burners entering through the shell
The round shape helps the flame swirl around the chamber, which spreads heat more evenly.
A word of caution about cutting old gas bottles
Cutting a cylinder that has held propane carries a real risk of fire or explosion from residual gas and odorant. People do this regularly, but the steps matter and mistakes can be severe. If you have any doubt, choose a different shell. A new steel pipe section, a clean steel can, or a disposable cylinder you know held only an inert gas and is fully empty are all options.
If you do use an old propane bottle, the precautions builders commonly describe include:
- Make sure the bottle is fully empty and depressurized before touching the valve.
- Remove the valve completely, outdoors, away from any ignition source.
- Fill the bottle completely with water and let it sit to displace remaining vapor before any cutting. Cut with the water still in it, or drain it immediately before cutting.
- Avoid sparks wherever possible during the first cuts.
These precautions lower the risk; they don’t remove it. Never cut a cylinder that might still be under pressure, and don’t use a cylinder whose contents you don’t know.
Materials and tools
Forge body:
- Steel shell (see above)
- Ceramic fiber blanket, commonly 1 inch thick, 8 lb density, rated 2,300°F or higher; enough for two layers
- Rigidizer (colloidal silica is common)
- Refractory coating or thin castable refractory for the hot face
- Hard firebrick or castable refractory for the floor
- Steel legs or a stand
Burner:
- Steel pipe for the burner tube, commonly 3/4 inch
- A reducer bell or reducing fitting for the air intake, plus a fitting to hold the gas jet
- A MIG welder contact tip as the gas orifice
- A short flare or nozzle at the outlet (optional, but common)
Gas train:
- An adjustable propane regulator (0–20 or 0–30 PSI types are common for forges) with a gauge
- Propane-rated hose and fittings
- A shutoff valve (ball valve) near the burner; a needle valve is optional for fine control
- Thread sealant or tape rated for gas
Tools: angle grinder with cutting and grinding discs, drill and bits, taps (helpful), wrenches, and a respirator for working with ceramic fiber.
Size the chamber and pick a burner count
Size the chamber to what you’ll heat. A small knife or hook forge doesn’t need a large interior.
- Estimate the internal volume after lining. For a cylinder, that’s π × radius² × length, using the inner radius after the wool.
- Use the common rule of thumb of roughly one 3/4-inch venturi burner per 300 to 350 cubic inches. Many single-burner forges come in at or below that size.
Remember that two layers of 1-inch wool take about 2 inches off the radius. A shell that looks roomy from outside can end up quite small inside.
Building the forge body
Prepare the shell
Clean off any paint, rust and grease, especially around the areas you’ll cut. Weld or bolt on legs so the forge sits stable and the burner points down into the chamber at the angle you’ve chosen.
Cut the openings and burner port
- Front door: big enough for your typical stock, but no larger. Some builders fit a sliding door or close part of the opening with a loose firebrick.
- Rear pass-through: lets long stock go through and gives exhaust somewhere to go. It’s optional, but often useful.
- Burner port: drill or cut it in the upper part of the shell, offset from center, so the burner fires tangentially. The flame should hit the wall and swirl around, not land directly on the floor or the work. Weld or bolt on a short tube or collar to hold the burner, with a set screw so you can adjust its depth.
Line, rigidize and coat
Line the shell with ceramic wool, rigidize it, then apply a refractory hot face. This is the step that most affects how long the forge lasts and how safe it is to use. It’s covered in detail in our guide to lining a gas forge with ceramic wool, rigidizer and refractory coatings.
Cut the burner hole through the wool cleanly. The burner tip usually sits flush with, or slightly recessed into, the inner surface of the lining.
Add a hard floor
Lay a hard firebrick, or cast a floor of dense refractory, on top of the wool. Bare or lightly coated wool won’t hold up to steel being dragged across it, and borax flux attacks both wool and insulating brick. A floor you can replace makes life easier. If you’re considering using bricks you already have, check first whether regular bricks are suitable for a forge.
Building a venturi burner
A naturally aspirated (venturi) burner uses the speed of the gas jet to pull in air. There are several well-known designs, and they differ in detail. The general layout is:
- Burner tube: a straight length of pipe, commonly 3/4 inch, several inches long.
- Air intake: a reducer bell or similar wide fitting on the back end, which gives the incoming air a large opening.
- Gas jet: a MIG contact tip held centered in the intake and pointed straight down the tube. Centering matters. An off-center jet is one of the most common reasons a homemade burner runs badly.
- Choke: a simple sliding or rotating plate that partly covers the air intake, so you can adjust the fuel-air mix.
- Flare or nozzle: a short, slightly widening outlet helps hold the flame at the burner tip instead of letting it lift off.
Contact tips come in different bore sizes. Builders commonly use small sizes on 3/4-inch burners, but the right size depends on the specific design. Follow the plan for the design you choose, and expect to experiment.
If you’d rather not build a burner, commercially made forge burners are widely available and take one variable out of your first build.
Gas plumbing: regulator, hose and valves
- Use an adjustable regulator with a gauge. Barbecue regulators run at a very low fixed pressure that most forge burners can’t use.
- Use propane-rated hose and fittings. Keep the hose away from the forge body and out of the path of hot metal.
- Put a shutoff valve within easy reach so you can kill the gas fast without reaching over the forge.
- Leak-test every connection with soapy water before lighting, and again whenever you change a fitting. Bubbles mean a leak.
- Keep the tank upright and away from the heat. Several feet away is sensible, more if the space allows.
First firing and curing
- Let any wet refractory and coatings air-dry fully, following the product’s instructions.
- Light the burner at low pressure, holding the igniter near the burner outlet and standing to one side of the door openings.
- Run several short, gentle fires to drive out remaining moisture before going to full heat. Some steam or crackling at first is normal; widening cracks or spalling are not.
- Gradually raise the pressure over later sessions.
From here, our guide to tuning a propane forge burner for a clean, hot flame explains how to dial in the flame. How hot does a propane forge get explains what temperatures to expect.
Common problems on a new build
- Flame burns inside the burner tube, or the tube glows. The mix or flow velocity is off. Check the orifice size and alignment, and how far the burner sits in the port.
- Flame lifts off the burner and goes out. Too much velocity or too lean a mix. Close the choke slightly or add a flare.
- Lazy yellow flame. Too little air. Open the choke and check the jet is centered.
- The forge won’t get hot enough. The chamber is too big for the burner, the openings are too large, or the lining is thin.
- The tank frosts over and the flame fades. You’re drawing propane faster than the tank can vaporize it. See how long a 20 lb propane tank lasts on a forge.
Quick answers
What’s the difference between a blacksmith and a forge? A blacksmith is the person who works the metal. A forge is the hearth that heats it, and the word is also used for a smith’s whole workshop.
What is the easiest thing to blacksmith for a beginner? Simple projects that mainly involve drawing out, tapering and bending, such as S-hooks, wall hooks and fire pokers, are common first pieces. They suit a single-burner forge well.
Can I use a propane torch instead? For very small work, yes, within limits. See can I use a propane torch for forging.