You don’t need an expensive forge to learn blacksmithing. Some of the most useful beginner forges are built from dirt, scrap iron and a few firebricks. The trick is knowing which corners are safe to cut and which aren’t.
What “on a budget” realistically means
A forge is only one part of a working setup. You’ll also need something to hammer on, a hammer, something to hold the hot steel, and safety gear. A budget forge leaves money for those. It shouldn’t cut corners on safety-critical parts like gas fittings.
The cheapest forges also tend to cost more in time and fuel. That’s usually a fine trade when you’re starting out.
How much does a home forge setup cost?
Prices vary a lot by region, by what you can scrounge, and with the market, so treat these as rough ranges, not quotes:
| Setup | Rough cost (forge only) | Notes |
|---|---|---|
| JABOD charcoal forge | Very low; often little more than a pipe and a blower if you have scrap wood and dirt | Charcoal is an ongoing cost |
| Brake drum coal forge | Low, especially if the drum is free from a scrapyard or garage | Needs some pipe fittings and an air source |
| Two-brick torch forge | Low; a few insulating bricks plus a torch you may already own | Only suitable for small stock |
| DIY propane forge | Moderate; the regulator, hose, wool and refractory add up | Plus the tank, if you don’t have one |
| Entry-level commercial propane forge | Moderate and up | Saves build time; quality varies |
Add the rest of a basic kit (anvil or substitute, hammer, tongs, safety glasses) and a modest home setup can still come in well under what new beginners often expect, especially if you buy used tools.
Cheapest option: a JABOD charcoal forge
“Just A Box Of Dirt” is exactly what it sounds like:
- Build a box from scrap lumber or sheet steel and set it on a stand or sawhorses.
- Lay a steel pipe across the box (black pipe, never galvanized) near where you want the fire. This is the side-blast tuyere.
- Fill the box with dirt, sand or a clay-rich soil and pack it around the pipe.
- Scoop out a trough in front of the pipe’s outlet to hold the charcoal.
- Connect any air source to the outside end of the pipe.
The dirt insulates the wood, and the fire sits in a pocket you shape by hand. Lump charcoal works. Some smiths break it into smaller pieces for a steadier fire.
Brake drum coal forge
Cast-iron brake drums are heavy, already bowl-shaped and often free or cheap from scrapyards and repair shops. Set the drum on a stand, fit a pipe tee to the center hole for air and ash, add a simple grate, and connect a blower. Our guide to building a coal forge firepot and tuyere covers the air connection and ash dump in more detail. You can burn coal or charcoal in it.
Two-brick or small brick forge with a torch
A few soft insulating firebricks with a hole bored through them make a tiny chamber you can heat with a handheld propane or MAP-Pro torch. It works for small items such as nails, small rod and simple hooks, but not much more. Read can I use a propane torch for forging before you rely on one.
For a larger brick build, see building a hard firebrick forge and our explainer on whether regular bricks work for a forge. Cheap red bricks and cinder blocks are a common budget mistake.
Low-cost propane forge
A steel can or shell, ceramic wool, and a homemade burner made from pipe fittings can make a capable forge for a moderate cost. The full build is in building a gas bottle propane forge and burners.
Fuel is the ongoing cost. See how long a 20 lb propane tank lasts on a forge to estimate your running costs.
Free and cheap air sources
Coal, charcoal and JABOD forges all need forced air. Cheap options include:
- An old hair dryer (set to no-heat or cool if possible)
- A shop vacuum on its blower side
- A small inflatable or bounce-house blower
- A secondhand hand-crank blower
Most of these blow far more air than a small forge needs. Plan on a gate valve, a sliding plate or a partial bypass to throttle them. The options are compared in forge blowers explained.
Where to save and where not to
Fine to save on:
- The shell and stand (scrap steel, an old drum, homemade legs)
- The air source (salvaged blowers)
- The anvil, at first: a heavy block of steel or a section of thick rail can stand in
- Tongs: many smiths make their own early on
Don’t skimp on:
- Gas regulator, hose and fittings. Use proper propane-rated parts and leak-test them.
- Ceramic fiber handling. Wear a respirator and cover your skin. Coat the wool rather than leaving fibers exposed.
- Ventilation. Every forge fuel can produce carbon monoxide.
- Eye protection.
Scrounging materials safely
- Avoid galvanized steel and pipe. Heated zinc coatings give off harmful fumes.
- Don’t cut tanks of unknown history. Residual gas makes this dangerous.
- Avoid concrete, cinder block and pavers near the fire. They can spall.
- Check salvaged iron for coatings, such as paint, oil or plating, and grind or burn them off outdoors before use.
Budgeting for the rest of the shop
Once the forge is sorted, a beginner’s priorities are usually: a solid surface to hammer on, one comfortable hammer, a pair of tongs that fits your stock, a bucket of water, and a fire extinguisher. Upgrade as specific needs come up. That includes the forge: plenty of smiths learn on a JABOD or brake drum and only later build something more refined. Our beginner’s guide to building a blacksmith forge and what is the best forge for beginners can help when you get there.
A quick note on the terminology: a blacksmith is the person; a forge is the hearth that heats the metal. “Forge” is also used for the smith’s workshop as a whole.