Metals and Fuel

Making Ingots from Scrap Metal

How to melt scrap aluminum, brass or copper into ingots at home: furnace, crucible, molds, the safety hazards that matter, and whether it's worth any money.

On this page
  1. Can you make ingots from scrap at home?
  2. Which scrap metals are practical to melt
  3. Why you can’t melt steel in a blacksmith’s forge
  4. Equipment you need
  5. Safety first: the hazards that actually hurt people
  6. How to make ingots at home, step by step
  7. Getting cleaner ingots
  8. The blacksmith’s alternative: forge-welding scrap steel into a billet
  9. Is melting scrap into ingots worth money?

Can you make ingots from scrap at home?

Yes, for some metals. Hobbyists commonly melt aluminum, and with more heat and care, brass, bronze and copper, into ingots using a small propane or charcoal furnace, a crucible and a mold. The process itself is simple: melt clean scrap, skim off the dross, pour into a preheated mold and let it cool.

The hazards are real, though. Molten metal and moisture can cause violent steam explosions, and some alloys and coatings give off harmful fumes. Read the safety section before you light anything.

Which scrap metals are practical to melt

Metal Approx. melting point Notes
Aluminum ~660 °C (1,220 °F) Easiest to start with; cast aluminum scrap gives the best results
Brass roughly 900–940 °C, varies with alloy Contains zinc, which fumes at these temperatures; needs good ventilation and caution
Bronze roughly 900–1,000 °C, varies with alloy Similar heat to brass; usually less zinc
Copper ~1,085 °C (1,985 °F) Needs a hotter furnace; pure copper can be tricky to cast cleanly
Steel ~1,370–1,540 °C Not practical in a typical hobby furnace or forge

Good aluminum sources: cast parts such as old lawnmower decks, transmission housings, pistons and other castings tend to melt well. Clean extrusions such as window frames are also usable. Beverage cans are a poor choice. They’re thin, coated in plastic and paint, and give a lot of dross and little metal.

Avoid: lead (toxic, and best left to people with proper controls), galvanised steel, anything painted or plastic-coated unless it’s stripped first, and any sealed or closed container.

Why you can’t melt steel in a blacksmith’s forge

A blacksmith’s forge is built to heat steel to forging and welding temperatures, not to melt it. Melting steel and holding it liquid long enough to pour takes higher temperatures, special crucibles and refractories, and serious safety measures. That’s outside what most hobby setups can manage safely. Blacksmiths who want a solid block of steel from scrap usually forge-weld it instead, as described below.

Equipment you need

  • Furnace: a small propane or charcoal furnace with a refractory lining. A forge isn’t the same thing, though some charcoal forges can melt aluminum in a crucible.
  • Crucible: clay-graphite or silicon carbide crucibles are common. Steel crucibles are sometimes used for aluminum, but they can slowly add iron to the melt and wear through.
  • Crucible tongs and a pouring shank that fit your crucible securely.
  • Ingot mold: cast iron or steel ingot molds, or a mold carved in a steel block. Never use a mold that might hold moisture.
  • Skimmer for removing dross, and flux suited to the metal if you choose to use it.
  • PPE: face shield over safety glasses, leather or aluminised gloves, a leather apron or jacket, natural-fibre clothing, full-length trousers over leather boots, and a respirator suitable for metal fumes for brass and bronze.
  • A dry sand or dirt floor under the pouring area, never concrete, which can spall violently when splashed with molten metal.

Safety first: the hazards that actually hurt people

  • Moisture is the number one danger. Water trapped in scrap, tools, molds or on the ground can turn to steam instantly under molten metal and throw it violently. Preheat everything that touches the melt, including scrap you add to a melt already in the crucible, tools and molds. Never add wet or cold, damp scrap to a full crucible.
  • Sealed and hollow objects can trap air or liquid and burst. Cut them open first.
  • Zinc fumes from brass and galvanised steel can cause metal fume fever. Melt brass outdoors with good airflow and a suitable respirator, and avoid galvanised material.
  • Coatings and plastics produce smoke and fumes. Strip them first or avoid them.
  • Burns and spills. Clear a path from furnace to mold, keep children and pets away and never pour over your feet. Have a dry sand bucket and a fire extinguisher at hand.
  • Carbon monoxide comes from fuel-fired furnaces. Only run them outdoors or in a well-ventilated space.

How to make ingots at home, step by step

  1. Sort and clean the scrap. Keep metals separate, cut off steel fasteners, remove plastic and paint, and make sure everything is completely dry.
  2. Preheat the mold by setting it on or near the furnace until it’s too hot to touch. That drives off moisture and helps the metal fill evenly.
  3. Heat the empty crucible in the furnace, then add a few pieces of preheated scrap.
  4. Add more scrap gradually as it melts, warming each piece first beside the furnace.
  5. Flux if needed according to the flux maker’s instructions.
  6. Skim the dross from the surface with a preheated skimmer.
  7. Pour smoothly into the mold in one steady motion, standing to the side rather than over it.
  8. Let it cool fully before handling. Ingots stay dangerously hot long after they stop glowing, especially aluminum, which doesn’t glow much at all.
  9. Knock out the ingots, label them by metal and source, and store them dry.

Getting cleaner ingots

  • Start with clean, similar scrap. Mixing random alloys gives unpredictable results.
  • Don’t overheat. Excess temperature increases oxidation and gas pickup.
  • Skim well before pouring, and avoid stirring dross back in.
  • Re-melt for cleaner metal if your first ingots are full of inclusions; the second melt usually skims cleaner.

The blacksmith’s alternative: forge-welding scrap steel into a billet

Since melting steel isn’t practical, smiths who want to use scrap steel typically:

Before welding a billet, make sure you know whether you’re working with low or high carbon stock. See mild steel vs high carbon steel for how they differ.

Is melting scrap into ingots worth money?

Usually not, if profit is the goal. Melting scrap mainly changes its shape, not its value, and costs you fuel, crucibles and time. Ingots are useful if you’re going to cast something, such as hardware, small parts or art pieces, or if you simply want compact, clean storage of metal.

How much is a 1 lb aluminum ingot worth?

Roughly what a scrap yard pays for a comparable grade of clean aluminum, and sometimes less. Yards may not know the alloy of a home-made ingot and may grade it conservatively. Scrap prices change frequently and vary by region and yard, so check with local yards for current rates rather than relying on figures online.

How many pounds of scrap does it take to make $100?

It depends entirely on the metal and current local prices. Copper usually pays far more per pound than aluminum, and aluminum pays more than steel. A small amount of clean copper can be worth as much as a large pile of steel. Call local yards for current prices.

What is the most profitable thing to scrap?

For most people, clean copper, such as stripped wire and pipe, tends to pay the most per pound among commonly found scrap. Brass and clean aluminum come next. Cleaner, sorted scrap usually pays better than mixed loads. Prices move with metal markets, so the ranking can shift.

The complete guide to metals and fuel

What Wrought Iron Is Used For
Read the guide

Keep exploring

Guides from other topics

All topics →