Quick Answer: The Terms You’ll Hear Most
If you’re just starting out, these are the words you’ll hear most often around a forge:
- Anvil: the heavy steel or iron block you shape metal on
- Forge: the hearth where metal is heated, and also a name for the workshop
- Tongs: tools for holding hot metal
- Drawing out: making a bar longer and thinner
- Upsetting: making a bar shorter and thicker
- Scale: the flaky black oxide that forms on hot iron
- Quench: cooling metal quickly in water, oil or brine
- Temper: reheating hardened steel to make it less brittle
- Forge weld: joining two pieces of metal by heating and hammering them together
- Heat: one session of heating metal in the fire, as in “it took three heats”
The sections below group more terms by category.
Parts of the Anvil
- Face: the flat, hardened top surface where most hammering happens
- Horn (or beak): the cone-shaped projection used for bending curves and rings
- Heel: the end of the anvil opposite the horn
- Hardy hole: a square hole in the face, near the heel, that holds hardy tools
- Pritchel hole: a smaller round hole used for punching through and holding some tools
- Step (or table): a lower, often softer area between the face and horn on many anvils, sometimes used for cutting
- Edges: the corners of the face, used for bending and shouldering. Smiths often round parts of them slightly.
- Waist and feet: the narrower middle and the base of the anvil
Forge and Fire Terms
- Hearth (firepot): the part of the forge that holds the fire
- Tuyere: the pipe or nozzle through which air is blown into the fire
- Bellows / blower: devices that force air into the fire
- Hood: the canopy that collects smoke and directs it to the chimney
- Coke: coal that has been partly burned to drive off smoke and impurities, giving a hot, clean fire (see coal vs coke vs charcoal)
- Clinker: a glassy lump of fused impurities that forms in a coal fire and has to be removed
- Breeze: small pieces of coke or coal
- Reducing fire: a fire with little free oxygen, which limits scale and is preferred for forge welding
- Oxidizing fire: a fire with too much air, which produces heavy scale
- Gas forge: a forge heated by propane or natural gas, common in modern shops
Hand Tools
- Cross-peen hammer: a hammer with a flat face on one side and a wedge-shaped peen on the other, and a common first hammer
- Ball-peen hammer: a hammer with a rounded peen
- Sledge: a heavy two-handed hammer, traditionally used by a striker
- Tongs: holding tools with jaws shaped for different stock (flat-jaw, wolf-jaw, V-bit and so on)
- Hardy (hot cut hardy): a cutting tool that fits in the hardy hole
- Hot cut / cold cut: chisels for cutting hot or cold metal
- Punch: a tool for making holes or indents in hot metal
- Drift: a tapered tool driven through a punched hole to enlarge and shape it
- Fuller: a rounded tool for making grooves and spreading metal
- Swage: a tool with a shaped groove for forming bar to a particular profile
- Swage block: a heavy block with many shaped holes and edges for forming work
- Flatter: a flat-faced set tool struck with a hammer to smooth surfaces
- Set hammer: a struck tool used to form sharp shoulders
- Slack tub: a tub of water for cooling tools and work
- Leg vise (post vise): a heavy vise with a leg that runs to the floor, built to take hammering
Forging Techniques
People sometimes ask about the “seven basic skills” of blacksmithing. Lists differ, but the core forging operations usually include these:
- Drawing out (drawing down): lengthening and thinning metal
- Upsetting: thickening metal by shortening it
- Bending: forming curves and angles
- Punching and drifting: making and shaping holes
- Cutting: separating or splitting metal with chisels and hardies
- Swaging and fullering: shaping with formed tools
- Forge welding: joining pieces at welding heat
Other useful terms:
- Tapering: drawing out to a point
- Shouldering: creating a sharp step between two thicknesses
- Scrolling: bending metal into decorative spirals
- Twisting: rotating a heated bar to create a twist
- Splitting: cutting a bar lengthwise to make forks or branches
- Flux: a material such as borax applied during forge welding to keep the joint clean
- Dressing: reshaping or tidying the surface of a tool or a piece of work
Heat Treatment Terms
- Hardening: heating steel to the right temperature and quenching it to make it hard
- Quenching: rapid cooling in water, oil or brine
- Tempering: gently reheating hardened steel to reduce brittleness. The surface shows temper colors from straw to blue as it heats.
- Annealing: heating and then cooling slowly to make metal as soft as possible
- Normalizing: heating and cooling in still air to relieve stress and refine the grain
- Decarburization: loss of carbon from the surface of steel when heated, which can leave a soft skin
Materials
- Wrought iron: a traditional low-carbon iron with fibrous slag, tough and easy to forge-weld, now rare
- Mild steel: low-carbon steel, the standard material for most modern general blacksmithing
- High-carbon steel (tool steel): steel with enough carbon to be hardened, used for blades and tools
- Cast iron: high-carbon iron that’s poured into molds. It’s brittle and generally can’t be forged.
- Stock: the bar or rod you start with
- Scale (firescale): the black oxide layer that forms on hot iron
Heat Colors
Smiths judge temperature partly by the color of the glowing metal. Colors look different in different light, so these are only rough guides:
- Black heat: hot but not visibly glowing. It can still burn badly.
- Dull red / cherry red: lower forging temperatures, often used for light work and some heat-treating steps
- Orange to yellow: typical forging heat for mild steel
- Bright yellow to near white: approaching welding heat
- Sparkling: the metal is starting to burn and is being damaged
People and Places
- Blacksmith: someone who shapes iron and steel by heating and hammering
- Striker: an assistant who swings the sledge under the smith’s direction
- Apprentice / journeyman / master: traditional ranks of training and skill
- Farrier: a specialist in hoof care and horseshoeing (see farrier vs blacksmith)
- Bladesmith: a smith who makes knives and swords
- Smithy / forge / blacksmith shop: the workshop (see what a blacksmith’s workshop is called)
Everyday Phrases That Came from the Forge
Several common expressions are often linked to blacksmithing:
- “Strike while the iron is hot”: act while conditions are right, just as a smith must hammer before the metal cools
- “Too many irons in the fire”: trying to do too many things at once, like a smith heating more pieces than they can work
- “Hammer it out”: to work something out through effort
- “Forge ahead”: to move forward steadily (this phrase’s link to the smithy is debated)
For more on the history behind these words, see Why are blacksmiths called black? and our guide to pioneer blacksmiths.